Well, 1 day down, 1/2 to go... Sergio does great work....

buc1980 wrote:Where you do that?How much?Mor Ryde Factory in Elkhart, In..... 8k axels, and disc brakes = $5800.00Hope they let you stay in your rig inside last night, instead of outside by the DRV's and trains :B Unless you just got there today. Be prepared to get up EARLY tomorrow morning. They sure know their stuff, and do it right. Make sure they give you a new, cool, puffy Mor Ryde sticker for the side of your coach. When you get your t shirts, go up at least one size. They run small.Did you get Jimmy Johns for lunch?Ours was supposed to take 2 days, but ended up taking 4.Congratulations. Hope you are as happy with yours as we are. Best money we ever spent.

The one problem there is that do not allow dogs in the waiting area,,,so you wind up in the truck with the pups.Ken

8K IS only.. Already had discs and 16.5 "H" shoes....got here at 1:00 pm yesterday, they did all thier measurments, figured on raising the rear by 2", that will put us at 13'1".Then the weighed eash wheel location and backed us in and took off the wheels.. We stayed in there last night, toured the area all day today, toures Redwood..Will be ( should be ) ready to roll tomorrow by noon.. $3200.00..while at it, i brought a box of American made Timken bearings, they tossed them on while at it..

MorRyde IS install , day 1 | Good Sam Community

21 Replies

Cummins12V98
Explorer III
Jun 20, 2016
ACZL wrote:
Looks awesome!!! Seems weird though not to see a axle tube going side to side.

Not a tube but there are two pcs of channel welded together that keep both sides tied together.
ACZL
Explorer
Jun 20, 2016
Looks awesome!!! Seems weird though not to see a axle tube going side to side.
ford_truck_guy
Nomad
Jun 19, 2016
Cummins12V98 wrote:
Saturday huh, really are busy!!!

I could not get out there early enough from eastern PA to get the job done during the week...
They offered that I pay the OT if the job did not get done by Friday
I opted to pay the OT for 4 hours on a Saturday for 1 tech.... They had a full plant operating Saturday till I left..
Cummins12V98
Explorer III
Jun 19, 2016
Saturday huh, really are busy!!!
ford_truck_guy
Nomad
Jun 19, 2016
Finished at MorRyde yesterday at 10:00 am....

Saturday was routing the brake lines , out if sight , and out of danger of damage from a blow out... And alignment ...
jnharley
Explorer
Jun 18, 2016
Sergio installed our 8K Moryde IS too.
Cummins12V98
Explorer III
Jun 18, 2016
laknox wrote:
Even in a blurry pic, those are =nice= welds, Cummins! :-) HEY! Lippert! Pay effin' attention!

Lyle

Keith worked on ours, he has worked there for at least 16 years. He is a person that takes great pride in his work. Once the lift was done they re routed all the brake lines so they are not very susceptible to damage if a tire blows. NICE tidy job. DRV are you listening?????
Cummins12V98
Explorer III
Jun 18, 2016
Garry&Gayle wrote:

Cummins how much for the lift job? I need the same done.

Contact Rob but It was just under $1,800 including tax.
Garry_Gayle
Explorer
Jun 18, 2016
Cummins how much for the lift job? I need the same done.
Gunship_Guy
Explorer
Jun 18, 2016
We had MorRyde IS on our last Mobile Suites. Really like that system.