Does anyone have a suggestion about how to install upgrades to the inside of the exterior, or the interior walls of an RV? Any links would be appreciated.I have a Rockwood Mini Lite, and it has very few structural members that would hold a screw well, even if I could find them, so I've been using Velcro.The hook-and-pile part is very strong, but the glue that's on the backs seems to be vulnerable to heat. Even a lightweight roll of paper towels came unglued. I tried super glue and epoxy to hold even this light of an object, but it didn't last.Just screwing in a wood screw or something would most likely not work very well. What's probably needed is some kind of expansion bolt. It would have to be very short so as to not compromise the outer hull, and have some way of expanding to affix to the back of the thin paneling that is on all of my walls, I would suppose.Any suggestions would be appreciated.

There are some 3M tape products that are rated for different weights that are supposed to work quite well. I understand that if the tape needs to be removed it doesn't leave any marks or scars on the wall also. Check with a good hardware store like Ace for the product.

I've had good success with Command Hooks in my camper and in the house. I've had the same Command Hooks up for years in my previous camper.Now, I did have one Command Hook in my home bathroom wall, and after a year, the clock it was holding fell. The glue was still holding, but the paint gave way. So the paint was still stuck to the tape and I now had a white spot on my wall. I ended up a nail.The other option is to use a hook - one of those Command style hooks, and put a drop of Liquid Nails behind it. But, it will never come off the wall then, unless you rip off the finish.

I use Command strips and hooks for most everything I want to attach. Only exception is a shelf I placed near the bed. Light items are no problem; for heavier items i use more strips. Never had anything fall off, and they can be removed. No holes.

Command strip hooks are the RVer's friend!2 large sized ones close together can hold the wife's massive handbags up. For things in the 10 pound and higher range those short collapsing wall toggles work well. Be advised they need a 1\4 inch hole for insertion.

Rockwood Mini Lite, exterior walls are likely 1" foam behind 1/8" or maybe even 1/16" luan. Interior walls will be about 1" empty space behind luan. Through luan into the foam, I've had moderate success with light loads using plastic expansion screw anchors. You have to use a short (3/4" or less) screw and shorten the anchor to match. I drill only through the luan, drive the anchor into the foam. You do not want to drill far, won't take but a couple seconds to make it through to the outside of the RV.Manufacturers embed anchor plates, heavier plywood or metal, into these laminated walls where ever they want to mount something. What you want to mount, you are on your own. Hollow walls, if it is too heavy for a stick-on (i.e. will pull off the wall paper) it is probably too heavy for an anchor. Without the foam to dig into, the anchor doesn't help much, and 1/8" of luan won't hold much by itself.Like some of the other posters, I like Command Strip, but they will be limited to the strength of what they are fastened to, and in a RV the weak point might be the wallpaper or fake wood plastic covering.

fastening items to RV walls | Good Sam Community

travisc
Explorer
Oct 14, 2013
My solar panels are held on the roof by 3M VHB double sided tape- very high bond. They haven't blown off yet.
Old-Biscuit
Explorer III
Oct 14, 2013
Your Mini Lite has aluminum wall studs...locate them then drill/screw into them for heavy items.
3M Command Strips for other items-------they 'stick' on----just have to properly clean area before attaching.

We have several pictures hanging in hallway of 5'vr and on walls in living area.
Large pictures with heavy frames. 6 1/2 Yrs of FT travel and they have never even budged
rockhillmanor
Explorer
Oct 14, 2013
Don't count of velcro. I found the glue part that sticks to the wall is no guarantee. Every time I have tried it they came right off the wall.

I had luck with only 'one' command strip and that was hanging something that hardly weighed anything. I basically gave up and have nice clean empty of anything walls in my MH. :B
eb145
Explorer II
Oct 14, 2013
I just put small wood screws in the wall panels. No problems yet - just don't screw them real tight so they don't strip the wall panel.

If a screw did rip out, I would just put a small toggle bolt in it.

Real easy and everything I've put on the wall is still there. No need for toggle bolts yet.

Ed
B_s_Bunch
Explorer
Oct 14, 2013
Our coach requires pop rivets for anything added to the walls. I have used the heavy duty 3m strips with good success so far. Larry
John_Joey
Explorer
Oct 15, 2013
Pop rivets, only way to go for certain items (i.e. spare fire extinguisher, toilet paper holder, spare towel holder, etc...)
taigarazz
Explorer
Oct 15, 2013
fo folks using command strips - Do you take pictures, artwork down before traveling, or do you leave it up?
DianneOK
Explorer
Oct 15, 2013
I leave them up....Also put tiny pieces of Velcro in strategic spots to keep things from shifting (pics, etc)
Handyman_Xenabl
Explorer
Oct 15, 2013
We use a lot of 3M (Command) products and even have a caddy on the shower wall, which is quite heavy when full of products.

No damage to the walls, nothing's fallen off yet - proper preparation of the surface is important.
Clay_L
Explorer
Oct 15, 2013
As stated above cleaning the surface is important. I use a spray cleaner and follow up with water then isopropyl alcohol. After installing the 3M Command strip I wait about 24 hours before adding the weight.
We have oil paintings (18 by 24 inches or so) with fairly heavy frames that have been up for ten years and 55,000 miles.

Forum Discussion

fastening items to RV walls

About RV Tips & Tricks

Related Content

Wall fasteners

Affixing items to walls of Lance Camper

Mounting Items

Fasteners: Metric or SAE?

Fasteners for solor panels