Torsion axle v spring axle

carringb wrote:
T

What you lose out on vs leaf springs is equalizers. Leaf springs can "walk" over bumps, so they work better for rough terrain and when the trailer isn't towed perfectly level.

To add to that, the equalizers keep the tire loading about the same. When a torsion axle steps over a bump, one tire may take the entire weight with the other carrying nothing. On my tandem torsion axle snowmobile trailer, I have often seen daylight under one of the tires. Those that worry about tire loads should consider using much higher rated tires on a multiple torsion axle trailer, but there goes any ride advantage.

I'm not sure what the question is, really. How do you know how "smooth" the trailer rides?
I've towed likely over 100 different trailers with both types of axles. Never give it a second thought. Shocks? What for? If you need shocks the trailer is overloaded. It should have enough spring rate to not look like a bobber fishing for bluegills.

Grit dog wrote:
Shocks? What for? If you need shocks the trailer is overloaded. It should have enough spring rate to not look like a bobber fishing for bluegills.

In Europe shocks are correctly called dampers. The purpose of the dampers are to control spring rebound. When a spring is compressed by a bump in the road it will quickly return to its normal position and somewhat farther. This will be the oscillations one sees when "shocks" are worn out. The stiffer the spring, the harder the ride because it will not compress as easily as a softer spring. The correct setup is to have the correct spring for the weight and control it's movement with dampers.

Grit dog wrote:
I'm not sure what the question is, really. How do you know how "smooth" the trailer rides?
I've towed likely over 100 different trailers with both types of axles. Never give it a second thought. Shocks? What for? If you need shocks the trailer is overloaded. It should have enough spring rate to not look like a bobber fishing for bluegills.

Not sure how you dont know...and if you dont...others around you and behind you sure do!

And shocks dampen spring movement, they are in no way related to the spring or spring rate other than having too much or too little dampening for the given weight and spring.

I added shocks to my TT last Fall, the first time doing so on any trailer, and I am super impressed. No bounce at all. It rides like its on a sheet of glass...well as much as my SUV does anyway. Highly recommended where possible!

Cant add shocks to a torsion spring axle, but then again, you would never need to. The rubber acts as the spring and dampener, all in one.

I prefer the torsion axles on my car hauler due to lower deck height for mild break over angles at the ramp and independent suspension movement at each wheel for better handling and ride.

I did upgrade from LRD tires and rims to LRE after my original set wore out at 30K miles knowing that an individual wheel may be taking the brunt of the load on one side, but this is rare unless you are doing nothing but off-road towing or you are towing off-level. I didn't have problems with my LRD wheels, but there was minimal cost to go to the higher rating and I hope to get better wear and puncture resistance with the heavier tires.

My car trailer is rated at 9900 lbs with dual 5200 lb torsion axles to keep it from being classified commercial (anything over 10K lbs in my state). I am typically loaded at 6000-8000 lbs and have not felt a need for shocks with this setup. My Weekend Warrior had dual 5600 lb spring axles and could have benefited from shocks since I was pretty close to axle and spring limits and could see the oscillations.

My snowmobile trailer with torsion suspension, rides nice, tows nice, and with wide stance axles, no sway, with no WDH needed. It is all aluminum, and has a 3,800 lb CCC. It sets low, for easy drive in/out.

For my FW, my leaf springs, with Equa-Flex works great in that application. I like having the high clearance. It all comes down to trailers use, as to what works best.

Jerry

Here is a pic of my snowmobile trailer, with the low riding torsion suspension.

Jerry

bluefishgary wrote:
Ok lets try this. How much does a spring axle go up and down??
How much does a torsion axle go up and down??

Depends on how fast you travel and over what type of road surface, and how much the trailer weighs.

Torsion is essentially an independent suspension. Superior to leaf (as we find it) in every way. Lower roll center, in essence. Think of it as wider track: wheel face at each axle end, versus leaf axle attach point some ways in from same.

Greater wheel travel, for starters.

Greater resistance to being upset, greater ability to smoothly handle broken surfaces, winds, etc.

And, it's pretty much irrelevant what OTHER types of trailers use; as in, make your high speed comparisons only with a TT.

One-piece beam versus thirty-or-so pieces on a single leaf. Last longer, and with no real maintenance.

A torsion axle is always an upgrade. It should be standard on a TT, but we live in the land of the clueless.

It must be towed level. Measure at home, and (as with any TT) get split Axle readings on CAT Scale to dial in. Scale operator can guide you on doing split reading.

.

durb wrote:
If I recall, Dexter does not recommend Torflex for triple axle applications.

I've read that from Dexter also. When I read the OP post I was wondering if his trailer had Dexters torsion axles ands how the trailer mfg got around Dexters recommendations.
However there are several torsion type axle mfg on the market.