After last weeks camping trip it looks like I need to upgrade my charging system.What I have now Parallax 7345 and small solar panel which seems to do real good at maintaining the 2 group 27 batteries in the summer.After researching on here and finding that the 7345 will take something like 3 days to recharge my batteries it looks like need to up date my converter :( (So much for firing up the generator and watching a movie while the batteries charge :?What I havent been able find online is for sure how to diable the stock conveter if I in stall something like this ?http://www.amazon.com/PowerMax-PM3-55-Amp-Power-Supply/dp/B004W8MQA8/ref=sr_1_11?ie=UTF8&qid=1382230443&sr=8-11&keywords=rv+converter+chargeror thishttp://www.bestconverter.com/PowerMax-PM4B-60-60-Amp-4-Stage-ConverterCharger_p_413.htmlI have plenty of room to mount it behind the old unit. that seams to work fine except for charging. Thanks Gary

Disable the stock converter:HYou will be replacing the stock with the NEW converter. No reason to keep old converter installed (keep as a spare maybe)Disconnect AC input to converterDisconnect battery cables on converterRemove old converterInstall new converter

I replaced my Parallax 7345 with this Progressive Dynamics PD4655V. Direct drop in replacement.

I replaced my Parallax 7345 converter with a Progressive Dynamics PD4645 converter a few months back. It's made to fit in the same space as the old converter.As already mentioned, disconnect shore power and battery ground wire before doing the swap.

You can keep both the old converter and the new one. Just switch the power off to the one you don't want to use. That way you can keep the Magnetek as an emergency backup, not that its necessary. If you have the space you could install a second circuit breaker for the new converter, or mount the new converter close to the battery and plug it into an outlet. Turn the CB for the old converter off.Personally, I replaced the old with a PD 9260.

Hi,If you keep both converters charging will be even faster.

Faster Chargeing | Good Sam Community

Old-Biscuit
Explorer III
Oct 20, 2013
Disable the stock converter:H

You will be replacing the stock with the NEW converter. No reason to keep old converter installed (keep as a spare maybe)

Disconnect AC input to converter
Disconnect battery cables on converter
Remove old converter
Install new converter
Bobbo
Explorer II
Oct 20, 2013
I replaced my Parallax 7345 with this Progressive Dynamics PD4655V. Direct drop in replacement.
CloudDriver
Explorer
Oct 20, 2013
I replaced my Parallax 7345 converter with a Progressive Dynamics PD4645 converter a few months back. It's made to fit in the same space as the old converter.

As already mentioned, disconnect shore power and battery ground wire before doing the swap.
tenbear
Explorer
Oct 20, 2013
You can keep both the old converter and the new one. Just switch the power off to the one you don't want to use. That way you can keep the Magnetek as an emergency backup, not that its necessary. If you have the space you could install a second circuit breaker for the new converter, or mount the new converter close to the battery and plug it into an outlet. Turn the CB for the old converter off.

Personally, I replaced the old with a PD 9260.
pianotuna
Nomad III
Oct 20, 2013
Hi,

If you keep both converters charging will be even faster.
time2roll
Nomad
Oct 20, 2013
Don't go bigger with the PowerMax as it does not hold voltage once the set point is hit. Once it hits 14.6 PowerMax drops down to 13.6 and you are back to slow charging. I think BFL13 measured about 75% charged when it steps down. The effect of a smaller unit will kick down at a higher percentage. Think 35a or 45a max with PowerMax and two batteries.

IOTA and Progressive hold voltage 14.2+ for an extended period and might serve you better. Going more amps with these is fine, especially the Progressive. Check your battery connection size before you go over 60 amps.
ScottG
Nomad
Oct 20, 2013
I was in the same position and replaced my 7345 section with a PDI 9260.
Made a huge improvement to how fast the batts charge and do a better job at maintaining them too.
BFL13
Explorer II
Oct 20, 2013
The PM4 is superior to the PM3. It does not need the batts to be low before it will do a bulk stage. The PM3 is like a WFCO for that. Also the PM4 has that Equalize goose during Float. Randy has that 3 yr warranty too.
mustangglp
Explorer
Oct 20, 2013
Thank for all the quick response's.
I read somewhere that if you leave the old converter hooked up it fool the other one into thinking the battery's are more charged then they are ?

If the power max cuts out at 75% that would better for battery life but would not be ideal for dry camping which is 100% what we do. The only time its plugged in would right before a trip or if I thought the battery's we're low. Which hasn't happened yet with the solar then again we haven't had any rain in the nine months I've had it.
I would just like to be able to run the generator for a couple of hours and not have to worry about running the heater all night
Gary
tenbear
Explorer
Oct 20, 2013
I wouldn't run both converters at the same time. The battery will only accept so much current so its hard for me to see that there is any advantage in running the Magnetek, at 3.8v, along with the PD (for example) at 4.4v. Run either one and switch the other off. Once the battery is 90% charged, or after 4 hours, the PD reduces the voltage and does not boil the water away.