Filling the gas tank

kellertx5er wrote:

DFord wrote:
If you can get at the fuel fill tube between the outside wall and the tank, check to make sure it and the vent hose are both slanted upwards toward the filler door. It sounds like the vent hose may have an kink preventing it from allowing air to exit the tank when gasoline is entering.

Fuel tanks for the last several decades have not had 'vent hoses'. Fuel systems are sealed for emission and safety reasons. Displaced air must escape through the filler neck.

Perhaps it's just a question of semantics, but there still is a vent hose (separate from the fill hose) that terminates at the filler neck. Blockage or other trouble with this vent hose will cause problems in filling the tank.

DFord wrote:
If you can get at the fuel fill tube between the outside wall and the tank, check to make sure it and the vent hose are both slanted upwards toward the filler door. It sounds like the vent hose may have an kink preventing it from allowing air to exit the tank when gasoline is entering.

Fuel tanks for the last several decades have not had 'vent hoses'. Fuel systems are sealed for emission and safety reasons. Displaced air must escape through the filler neck.

NinerBikes wrote:
That'll get ya the Order of the Crescent Moon scar around your eyebrow, cause the only way to get the accuracy at extended range is to shoot from the prone position, off of a rest... and that Telescopic sight has a good chance of drawing blood, possibly needing stitches, when it pops ya but good.

No "Order of the Crescent Moon" membership here ... my BAR 300 Win Mag has an adjustable muzzle break. :)

P.S. My setup is why I laugh at the AR 15 and related stuff ... they're really just popguns.

pnichols wrote:
Or ... if you don't wanna stalk nor get 7 mag close ... try 300 Win Mag. ;)

That'll get ya the Order of the Crescent Moon scar around your eyebrow, cause the only way to get the accuracy at extended range is to shoot from the prone position, off of a rest... and that Telescopic sight has a good chance of drawing blood, possibly needing stitches, when it pops ya but good.

Or ... if you don't wanna stalk nor get 7 mag close ... try 300 Win Mag. ;)

Remmag wrote:
Thanks for the responses! (9erBikes that would be 7mm)

My hunting buddies have always told me that 7 Mag owners buy it to compensate for poor stalking skills, and that a 270 Win was superior, around a lot more years, and had far more kills.

Thanks for the responses! (9erBikes that would be 7mm)

Our 2005 E450 Itasca Class C has done that for the 10 years that we've owned it. The automatic nozzle shutoffs at gas station pumps stop with the tank at least 5 gallons short of full.

However, I've learned a way around it. I "trickle fill" 5 more gallons into the tank after the nozzle tries to shut off the flow - by carefully feathering the nozzle trigger to get 5 more gallons to dribble into the tank. It probably takes another 6-7 minutes of standing there to do this, but I wind up with a full tank. This takes patience ... and only 70 to 80 percent of the nozzles allow you to do this. Some nozzle shut-offs are so sensitive that you can't dribble any more gas through them after they want to shut off.

It's worth it to me because I hate stopping for gas and I like a full tank before heading off-pavement so that we as much as possible have plenty of fuel for long generator runs, if needed, for battery charging or running of the A/C in hot weather. I've even had attendants come out and ask me if the pump is working OK ... probably because of my sometimes long fill times.

Since our Class C is only 24 feet long our fill nozzle is very close to the stock rear tank location so I'm not sure how much, if any, Winnebago had to extend the fill pipe location.

Per my observation the filler-vent tank tubes are at the bottom of the priority list with manufacturers.
Recently I drive F350 pickup that I converted from utility body to dually bed.
Had to run the hoses from rear tank to new fuel neck.
Even I tried to do it the simplest way, the design is not making it easy.
So I ended up with neck, that require certain nozzle position to fill up without nozzle popping up constantly.
In my case it is about 10 degree CCW. I hope you can find yours.

It's important to note when replacing those pieces of "hose" to make sure you get hose rated for "gas lines" I found NAPA carried the bigger sizes - like the 1-1/2" hose for the filler. Radiator hose will deteriorate very rapidly when exposed to gasoline.