Suge Protect 50A and Generator ?

After the transfer switch. Protect all of your valuable AC products in the RV. My first RV had a gen that failed and output 160v. Luckily, I had wired my PD after the transfer switch. Even then, it managed to fry the microwave before it tripped.

I agree with installing between transfer switch and the breaker panel.
Protecting the transfer switch is overrated IMO. Easy swap if you carry a spare.
otoh there are posts about generators that produce bad voltage. You can't carry a spare everything else if the voltage regulator goes wonky.

Power systems before the transformer meaning line transmission and distribution have cutout relays to shunt lightning strikes to ground. A bad secondary strike can blow a transformer off a pole, turn park wiring incandescent, make a Hughes Autoformer, or "Energy Management System" look remarkably similar to a turkey baked in an oven 36 hours, and fry a lot of circuits downstream from that.

I tune an AM radio off-station. If I hear crackling getting louder the plug gets yanked.

Lantley wrote:
I guess what we disagree on is the genset surging. We know a power surge at the pedestal can happen for a lot of reasons including lightning and storms. I see it as I have a 99% chance of a surge coming from the pedestal vs. a 1% chance of the surge coming from the genset.
Furthermore you guys are talking about the transfer switch possibly being damaged, what's stopping the surge from damaging the genset itself if the protection is after the transfer switch?
My rig spends 99% of its life connected to the pedestal and very little time on genset power. Genset surges are possible but extremely rare. Genset have there own circuitry to avoid surges.
Nevertheless we each can decide for ourselves. I'll place the protection where I believe the potential problem is and take my chances on a remote genset surge. Especially if that means exposing the genset to surges from the pedestal.

The generator is isolated from the post by the transfer switch so it would not be affected by a line problem. IMHO Gary

I guess what we disagree on is the genset surging. We know a power surge at the pedestal can happen for a lot of reasons including lightning and storms. I see it as I have a 99% chance of a surge coming from the pedestal vs. a 1% chance of the surge coming from the genset.
Furthermore you guys are talking about the transfer switch possibly being damaged, what's stopping the surge from damaging the genset itself if the protection is after the transfer switch?
My rig spends 99% of its life connected to the pedestal and very little time on genset power. Genset surges are possible but extremely rare. Genset have there own circuitry to avoid surges.
Nevertheless we each can decide for ourselves. I'll place the protection where I believe the potential problem is and take my chances on a remote genset surge. Especially if that means exposing the genset to surges from the pedestal.

Thanx for all the info and opinions. That is why I asked the question.

Lets see a transfer switch would cost about $200 to replace if it got fried. If generator spikes(fails anyway it can) you would fry anything electrical fin the RV. Just about anything electrical after the transfer switch is going to cost more than the transfer switch. Put the protector where you think it will be the most cost effective for you. JMHO Gary. You know where mine is. I would rather replace the transfer switch.

Lantley wrote:
I agree the genset can fail. But honestly I consider the risk of the genset frying everything very slim vs. a surge coming form the pedestal.I want the protection as close the pedestal as possible.
Maybe I may fry my 50 amp cord if a large surge strikes However everything after the EMS 50 should be protected.
If surge is installed after the transfer switch than the transfer switch itself could fry along with more internal wiring if the pedestal produces the surge.
I'll take my chances with the genset and focus protection to issues coming from the pedestal.

So, let me summarize, risk losing everything on the rare occasion of a genset failure, or, risk losing the transfer switch on the occasion of a pedestal failure.

Is that a correct summarization?

The OP can take his choice of the above. That is why we say YMMV.

I agree the genset can fail. But honestly I consider the risk of the genset frying everything very slim vs. a surge coming form the pedestal.I want the protection as close the pedestal as possible.
Maybe I may fry my 50 amp cord if a large surge strikes However everything after the EMS 50 should be protected.
If surge is installed after the transfer switch than the transfer switch itself could fry along with more internal wiring if the pedestal produces the surge.
I'll take my chances with the genset and focus protection to issues coming from the pedestal.

I have mine after the transfer switch. As posted above the generator can fail. I would rather replace a burnt up transfer switch than the electronic after the transfer switch.