I would like to have a warmer TC floor... any ideas?

Heated door mat 24x36 just plugs in 180 watts
From a link on the heated floor page.



That's got to keep the tootsies toasty.

I spent three days getting as much done as possible which included installing a new Airfoil, changing loading guides, and remounting the camper on the truck. Got the horse pads fitted too.

I was. Informed that I would be having surgery on Friday January 26th and that I wouldn’t be able to do anything for at least three weeks and very little for a couple of months.

I busted my tail for three long days so that the camper would be ready by the surgery and be ready during the end of my recovery. March is a great time to head south and then move back north following the ideal temperatures. I should be ok if I can get help with the propane bottles.

Today was my first good day and I used it to do my income taxes... going to get some money back this year... all of that tax we paid getting the camper rebuilt changed our federal tax in a very positive way.

Thanks for everyone’s thoughts on my cold floor... it seems that the tub surround is the coldest part. I’ll get it wrapped before next winter... electrically like boatycall call and someone else mentioned has promise.

I have some reading to catch up on.... a day at a time

Thanks

Chet

Chet, I got it!

I've been keeping up on this as time goes on, and I did see the electric ribbon solution. This is similar.

This is very low cost, and very low-wattage draw, so it can run off inverter and your solar should be able to keep up. They rate it at 12watts draw per SqFt.
Just add a thermostat and you're set.... You wouldn't even have to hardwire it, you could simply add a plug at the end of your wiring and plug it in.


110v heated floor mat

Still haven’t decided on the tub wrap mareral.

I put the camper back on the truck to look for pinch points... and determine just how thick that the sheets of Low Density Polyethylene can be.

I installed a new replacement Airfoil today.... ****, it was cold outside. I need to get as much ready as possible before March

We like the spring and fall for moderate weather. I’m getting a butt trim on Friday, that will interfere with my projects for a little while.

BTW... for those of you that haven’t handled a rubber Matt... there is about as much rubber and weight as a very big truck tire.

Thanks for your comments

Chet

I must be stupidly stronger than I thought. I folded the first one in half and carried it in front of me thinking I was wimp when my biceps started to burn half way across the parking lot. Then I did it again with the second one. I don't go to the gym or work out and thought I was just soft and need to carry these mats more often.

I forgot about the weight but then again I had the guys at the feed store load them in the bed and I cut them in the bed. I never actually had to lift the full weight. Plus I think I am a tad younger and bigger than you are Chet. sorry about that

I finished cutting the Matt’s to fit today... I completely covered the truck bed floor.

I worried about the extremely heavy weight and managed to remove about 10.2 sqft which is about a forth of the rubber mats original weight.

I tried everyone’s way to cut but kept on going back to the circular saw.

I will say again that the mats are extremely heavy...especially for us old guys. None of you mentioned the weight.

I placed the side with the round “ buttons” down againest the truck bed... them and the structural rails pressed into the truckbed should allow that are to drain if ever needed.

Now for the tub surround insulation.

Chet

jimh425 wrote:
I watched a YouTube on how to cut them. Utility knife soaked in soapy water. Multiply passes with a board screwed as an edge to follow. Works well.

X2
I used a 2x4 shoved under the mat so that the utility knife cut would "spread" and not drag on the knife. Multiple passes work.

I watched a YouTube on how to cut them. Utility knife soaked in soapy water. Multiply passes with a board screwed as an edge to follow. Works well.

I used my jig saw to cut them around the wheel wells and the skill saw for long straight cuts