Life with a trailer behind...

Another recommendation for a back up camera.

I use the camera system for both, my travel trailer, and my truck camper. I have one monitor (clips onto the rearview mirror) and three cameras. One on the travel trailer (permenantly mounted with cabling to front of the trailer), one for hitching up the travel trailer, and one for combination rear view / hitching up a utility trailer, with the TC. I wired the truck with extra long video / power cable, and plug in which ever camera I am going to use. I have the cable coiled up by the tailgate, and pull out what I need to plug in which ever camera.

On the TC, I use velcro straps to mount the camera, either on the ladder for road use, or, on the hitch receiver for hitching up the trailer. It's a great help for backing the trailer.

My 7x14 has twin axles with torsion bars. Based on the fact that nothing shook loose on my 500 miles trial run I guess it rides pretty smooth.

I have now learned not to let the wiring drag on the highway. I chafed right through it and had to make up a new harness for it. Live and learn.

If you have torsion axles, the only thing you can do is re-index the arms for more lift. I prefer to keep mine low - It tows like a dream without sway control and only weight distribution.

One trailer experience that I had to deal with was lack of clearance on my jeep hauling car trailer. It is a wood planked, minimalist, 14'x7', 7K pound max, flatbed weighing in at 1100 pounds. I kept dragging the tongue or tail on dirt roads and going into abrupt gas station driveways.
Since the trailer had spring under leaf springs/equalizers the solution was to convert the suspension into a springs-over-axle format. It was a simple and fast process. The axle was square, so the springs-over was a snap: no new spring pads needed. Just reverse the u-bolts. It took two high lift jacks, two floor jacks, and four tall jack stands on 8x12's to get the bed hanging in space, momentarily. Disconnect one end of the leaf springs to release the axles. I gained about 3.5 inches of lift, which also gave me more space inside the fenders for larger tires, if needed be. I haven't dragged tail since.
For jeep use, I leave the ramps at home and have installed two, crank up/down, pivoting, 2 ton trailer jacks on the side/rear and just lower the jacks to the ground and drive the jeep off and on using the ARB air lockers and 130:1 crawl.
Actually that was then and this is now. I'm selling my beloved Scrambler and the car trailer goes with it. See Reno/Tahoe C.L. for details.
I can't see why an SOA lift wouldn't work on an enclosed trailer if you want to make the dragging and screeching go away.
jefe

X2 on the torsion suspension axles. 2 of our trailers have them, our 2 horse trailer and our 16ft stock trailer. Yes they ride much better and since the cargo in these trailers is usually livestock less abuse is good.

I only have one camera, on the camper bumper. Wire length limited me to mounting it there - it's the OEM camera for the GM NAV system.

For those that may happen across this thread in the future and are considering a trailer, I'd highly recommend getting one with torsion suspension axles.

My 6x12 had them.
My 8.5x20 has them.

I've been using my brother's 7x16 leaf spring trailer after selling my 6x12, and it bounces all the time. Every little imperfection in the road is transmitted to the truck. I never experienced that with the 6x12.

Torsion axles make for a smoother ride, due to each wheel being able to move independent of the other - think Independent Suspension. A smoother ride means your cargo doesn't take the abuse like on a leaf spring trailer.

I only have one camera which is mounted on the back of the TC. I flat tow my toad, not a trailer. I can see my tow bar and behind the Samurai. If I could back up, which I cannot, the camera is high enough for me to see where I was going. I would have little improvement with an additional camera. I could adjust the camera down and see the entire hitch and two or three car lengths behind the Samurai. I prefer to see further back.

If you purchase your camera from a reliable source that is in the camera business, you have several options. I purchased from RV Cams.

Wayne

Those of you with cameras, do you have one on the back of the trailer as well as on the back of the truck/camper?

I am definitely putting one on the back of the camper to see the hitch area and trailer but I bet it would be real nice to have one all the way back on the trailer.

Anyone have that?

Hi Jgwoods - couple things you might try with your shorter trailer:

Find a nice big quiet parking lot and back around the place putting your trailer between the lines till you can do it blindfolded :)

"look up!" before backing into anyplace :)

All very good advice, bottom line practice practice practice. One thing I'll add, my 7x12 has stabilizer legs that drop down in the rear. If I'm unhooked and drive my dresser in the tounge, will come off the ground. Only did this once, not a good feeling.