I just went to my local Camping World and picked up two black Ultrabreeze vent covers. But I think I have run into a slight snag. Work & Plays have flat metal roofs. Around the base of each vent fan is all that gooey sealant. There is no flat surface around the edges or anywhere to mount the Ultrabeeze into the existing frame of the vent fan.So, will I need to go back and get the MaxxAir vent covers? The MaxxAir covers bolt into the side of the existing vent fans. The Ultrabreeze does not. Unless I'm missing something, I think I've hit a roadblock here.Fortunately, our Camping World is about 3 miles from the house. Plus the MaxxAirs appear to be cheaper unless I go with the MaxxAir II. What say you? If I have to get the MaxxAir, should I go with the MaxxAir or MaxxAir II? Are they worth the little bit extra. Both models get really good reviews.

I looked at the Ultrabreeze before I bought the MaxxAir II's. I'm not sure how the Ultrabreeze mounts as I never got that far. If you go with MaxxAir, I recommend the II's as they allow the vent to open up farther and flow more air.It's possible the Ultras wont' work at all for you because of your roof design.

I would go with the MaxxAir over the Ultrabreeze everytime, the Maxxair is a better pick because of the way it mounts,to the sides of the vent instead of opening up the roof and having to replace all the sealant.Ether MaxxAir or Maxxair II will work well I have used both but like the look of the MaxxAir.If you are going to put it over a fan a MaxxAir Fanmate was my choice. It opens so you can clean the fan and vent. The video shows it very well.

Looking at the Fantastic video for mounting the Ultra Breeze, you remove two screws on each side of the vent, put the mounting brackets on and then the cover which is mounted with carter pins to the bracket. The video shows the demonstrator doing it in less than two minutes.

Then install doesn't bother me so much as the looks of the Ultra Breeze. Maxxair has a much more appealing look, but the UB is functionally better. I need 2 covers in the near future and they will most likely be UB. Cutting a little bit of Dicor out and removing a few screws then pouring fresh Dicor over the bracket isn't that big of a deal to me.

philandterri wrote:Looking at the Fantastic video for mounting the Ultra Breeze, you remove two screws on each side of the vent, put the mounting brackets on and then the cover which is mounted with carter pins to the bracket. The video shows the demonstrator doing it in less than two minutes.I can't even see my screws. They are covered with sealant all the way around the fan.I'm going back tonight to exchange for some MaxxAir covers.

Ultrabreeze vs. MaxxAir | Good Sam Community

Ron3rd
Explorer III
Jul 26, 2014
Mr. C wrote:
Sandia Man wrote:
MaxxAir II is what we used and they work well over our vent fans, simple to clean as they lift up on one side.

Do these allow the lid to be opened all the way? I'm going to be installing Vortex II fans and will not be replacing the lid or housing.

$64 on Ebay. $112 at CW. There is no warm, fuzzy feeling...

No, the lids won't open all the way, maybe 2/3 of the way. No issue with us however. The best IMO is the cover made by Fantastic but they were too pricey for my taste. With those, you can open the lids all the way, or very close to it.

Fantastic Vent Cover

DEMO ON YOUTUBE
Mr__C
Explorer
Jul 26, 2014
Sandia Man wrote:
MaxxAir II is what we used and they work well over our vent fans, simple to clean as they lift up on one side.

Do these allow the lid to be opened all the way? I'm going to be installing Vortex II fans and will not be replacing the lid or housing.

$64 on Ebay. $112 at CW. There is no warm, fuzzy feeling...
jeeperdude10
Explorer
Jul 26, 2014
Unfortunately it is a 'sad state of affairs' we have anymore. Seems no one is accountable for ANYTHING, and offer words to help soothe, but the issue(s) seem to always be overlooked and hardly ever resolved. Good luck dealing with CW.
lawnspecialties
Explorer
Jul 26, 2014
I will definitely install them myself if I can ever get them.

Ordered them last week on Wednesday. They said the truck order was too late so they would be here this Friday at my local Camping World. Well you know where this is going.

Went today to pick them up and for no reason, they weren't on the truck. Computer showed 102 available on the east coast but I guess not in Raleigh.

Retail manager was very apologetic and is supposed to call me tomorrow for more details. We leave next week so I'm curious as to what they'll do.
Ron3rd
Explorer III
Jul 25, 2014
I would check with another CW and see what their policy is on installing Maxxairs and how they do it. Hard to believe their policy is to "screw them down to roof" which places more liability on them in terms of leaks. Seems like they're doing it the hard way by drilling all those holes. I'd be an un-happy camper if I could not pull the pins and fold over my MaxxAir IIs for cleaning.
jeeperdude10
Explorer
Jul 25, 2014
I did try and showed my disappointment in their installation....wrote to CW to explain my DISGUST, and all I got was "we can offer you a ONE TIME leak test"...Yeah Right like I am going to do that, because that will make the install RIGHT??!! Seems 'quick and easy' is the way of this world anymore....no sense of accountability/pride in one's work/work ethic. I am DONE with CW for anything other than what is on the shelf.......
Cummins12V98
Explorer III
Jul 25, 2014
If they did not install per mfg specs I would go after them.
jeeperdude10
Explorer
Jul 25, 2014
Exactly.........when I inquired why...and if they would've told me that is the way they mount them. I would've done it myself. But coach was in for other things so I 'guessed' they knew what they were doing...but found out that they do not. I corresponded with MaxxAir and they have sent me the mounting brackets, no charge (they are very reputable). So now, I am perplexed as to the 'crud' build up under cover and compromising TPO/EPDM. I have even given it a thought of "unscrewing ALL bolts, caulking like heck, and rescrew back into same holes....then mount covers as per MaxxAir specs". Probably over kill........"What to do"????????
Ron3rd
Explorer III
Jul 25, 2014
jeeperdude10 wrote:
I strongly suggest you do it yourself if you can. I purchased 3 MaxxAirs in 2011 from CW and had them install.....my bad,, as they mounted them DIRECTLY to the roof of my C. So now I have 12 extra holes in the roof I need to 'worry' about. When got coach home and noticed the install, I called CW and was told "that's the way we mount them here"-REALLY?! I was offered a one time leak test, which would have really put my mind at ease. Anyway, my biggest concern is-will the EPDM roof be compromised under the cover, due to dust, stuff build up overtime, as I cannot clean other than by spraying water under such, or is this enough. We have been in some HEAVY downpours and thank God no leaks.....

Odd they would mount them that way since they come with all the necessary hardware to make them quickly removable. Somebody didn't read the instructions or didn't know what they were doing.
jeeperdude10
Explorer
Jul 25, 2014
I strongly suggest you do it yourself if you can. I purchased 3 MaxxAirs in 2011 from CW and had them install.....my bad,, as they mounted them DIRECTLY to the roof of my C. So now I have 12 extra holes in the roof I need to 'worry' about. When got coach home and noticed the install, I called CW and was told "that's the way we mount them here"-REALLY?! I was offered a one time leak test, which would have really put my mind at ease. Anyway, my biggest concern is-will the EPDM roof be compromised under the cover, due to dust, stuff build up overtime, as I cannot clean other than by spraying water under such, or is this enough. We have been in some HEAVY downpours and thank God no leaks.....

Forum Discussion

Ultrabreeze vs. MaxxAir

About DIY Maintenance

Related Content

Fantastic Fan vs Maxxair vs something else

MaxxAir vent covers

Fantastic ultrabreeze vent cover-recommend?

Fan-tastic Ultrabreeze Vent Cover

MaxxAir cover on a van?