They are 4" flange mount and Im having a dickens of a time picking out the myraid of 4" options. Some say 5in with 4 lens etc etc. I just want to find a set that would fit the stock and change me over to LED stop turn tail. Going to replace the white backup lights (usless pretty much) with Stop Turn tail and wire them with the outside stop turn tail.So anyone done it ?

I will follow this am thinking of doing the same

It might be easier to just replace the old bulbs with LED bulbs.

Ava wrote:It might be easier to just replace the old bulbs with LED bulbs.Did that, they are not as bright as the incandescence and people that follow me in the RV group I belong to said that its hard to see the brake lights at times.

I do not have a Everest but I do have A 2004 Challenger which was the sister of the Everest. I put 4 of these on the back of mine. They are surface mount and I ran 2 of them Vertical to cover the screw holes from the old Bargman lights. They are very bright and have had no trouble with them for 8 years now.

pending the source of the leds they can be worse than junk. the better ones will blind any behind you. only takes money.pay the price, buy the best. and only cry once.

Anyone own a Everest and replaced the Tail lights with LED

WeBeFulltimers
Explorer
Mar 13, 2018
aruba5er wrote:
why spend the time and money? a 1157 bulb was designed for your tailight and the present light meets DOT standards It's not like you need to save power or the fixture makes too much heat. Now if it was interior lighting, thats a differant story, where you can save battery power and get much needed light. Forgetaboutit.

Totally agree. I trucked for 20 years and worked at night most of that time. Rarely saw campers traveling at night. Why change them out if you are parked somewhere at night anyway?
W7PSK
Explorer
Mar 12, 2018
The ones I got were grommet mount. Unfortunately the Everest has molded receptacles for the lights so Flange Mount is required. I cant seem to find any good ones. We head out next Friday so Im going to replace the LED bulbs back to stock and wait till I find some good LED lights next time.
routemaster
Explorer
Mar 11, 2018
Rick. I droped the back up wire down and bought two lights and mounted them below.
Den.
blofgren
Explorer
Mar 11, 2018
routemaster wrote:
Yep.Here you go.

American Superlite Model SL4000

Those look very similar to ours, only ours already has the 2 lights per side in addition to the reverse lights.
W7PSK
Explorer
Mar 11, 2018
routemaster wrote:
http://www.empirechromeshop.com/p-1528-american-superlite-red-4-round-15-diode-led-stopturntail-light.aspx
Rick shop around.
Den.

Thanks Den, think I found a nice set.
Ill remember about drilling the hole when I install them. Heading to Phoenix next week and wanted them installed and ready to go. Never use the back ups so converting them to Stop Turn Tail.
routemaster
Explorer
Mar 10, 2018
http://www.empirechromeshop.com/p-1528-american-superlite-red-4-round-15-diode-led-stopturntail-light.aspx
Rick shop around.
Den.
routemaster
Explorer
Mar 10, 2018
Rick.On the lens it stamped SL4000,I drilled a hole between the two pockets so as to conect the lights to gether four stop and two and two turn.
Den.
W7PSK
Explorer
Mar 10, 2018
routemaster wrote:
Yep.Here you go.

What model are those lights, I have the indentations like you do, so The long oblong like jjj's wouldn't work. Those would.
routemaster
Explorer
Mar 10, 2018
Yep.Here you go.

American Superlite Model SL4000
aruba5er
Explorer
Mar 10, 2018
why spend the time and money? a 1157 bulb was designed for your tailight and the present light meets DOT standards It's not like you need to save power or the fixture makes too much heat. Now if it was interior lighting, thats a differant story, where you can save battery power and get much needed light. Forgetaboutit.