Hi all. I'm wondering if its possible to flip my WDH. (I would upload a picture but its a hassle here, I'm on a tablet only.) THe kind I have is the type that has the L part that goes into the reciever on the truck, that has three holes in it where the other part attatches to it via 2 big bolts (one hole is free, for adjustment I suppose) with the springs mashed inbetween. I got this setup when I had a much lower vehicle than I have now, and with the 2 1/2" lift I recently put on my truck I have to put a block under the front wheel to be able to crank it up far enough to get the trailer over top of the ball LOL. So what I'm asking is how difficult would it be to take it apart so the L part is now pointing down instead of up, put it all back together so the ball is 4-5 in lower. Is there anything special tool wise or procedure wise to do this, or is it as simple as it looks?

If I understand correctly what you propose doing, they are intended to be used that way. No special tool, the idea is to make both the TV and the trailer sit level. To that end, you have to do what you have to do.

Just make sure you torque the bolts to the proper spec once you "flip" the shank. Local hitch shop may be able to help for a few $ if you don't have the right size tools.

Theres a big RV place pretty close but. Im sure they would charge an arm and leg though. Thats why Im asking if it can be done myself.

Ball height is best determined by how the trailer tows. Should be close to level for best performance and stability. Many WD hitches come with an adjustable height ball mount so you can achieve the proper height and these will work either way you flip them but again, based on your need to get a near level tow.Good luck / Skip

Thanks everyone. I have about 2 months to do it, but i also want time to test it at least once.

Flipping a weight distributing hitch? | Good Sam Community

12 Replies

APT
Explorer
Apr 30, 2015
Some shanks are not designed to be used in the rise position. Take a look at this page. My WDH came with the 54970 which can be used either way. When I replaced my TV, I need a lower drop. So I replaced it with 63971 which is drop only. If you are in rise position now, I would flip it, remount the head, and readjust the WDH. I have never heard of a WD head that is designed for rise only.
kamperdog
Explorer
Apr 29, 2015
Hmmm, im actually concerned about not enough tongue weight now LOL. Maybe I'm just so used to it being so high. I'm gonna test this setup out this weekend on a short local camping trip about 20 miles away and see how she does....
cbshoestring
Explorer II
Apr 29, 2015
Ideally, the trailer should sit level, If you are still 2 1/2" high of the trailer, then YES, I think a new shank may be needed.
kamperdog
Explorer
Apr 29, 2015
So you think the hitch on the truck should be even lower than it is?
cbshoestring
Explorer II
Apr 29, 2015
kamperdog wrote:

I flipped it and at the lowest setting its still is 2.5" higher than the trailer when I have it (the trailer) sitting perfectly level. .

You may need to buy a new shank, if the old one isn't getting you level. When I went from my Dodge Dakota (bar was set to raise trailer) to my RAM, even flipped it did not get me low enough.

EDIT: When I got mine back together, and set for my trailer, I stopped my the local garage with it's door open. I DO NOT have a torque wrench that does 300lbs, but they did. He set me up with nothing more than a thank you, so the next morning I delivered a dozen donuts.
kamperdog
Explorer
Apr 29, 2015
I have the exact same sway bar set up and my hitch is nearly the same,thanks for the pictures.

I flipped it and at the lowest setting its still is 2.5" higher than the trailer when I have it (the trailer) sitting perfectly level. My trailer has a relatively light tongue weight at 320lbs. Should I raise it one hole ( I guess thats an inch) for more trailer "push down" weight on it?

It actually seems like it would be perfect but I want to get some more opinions on whether or not theres sufficient tongue weight so nothing bad happens lol.
2manytoyz
Explorer
Apr 29, 2015
You can certainly do this with an Equalizer hitch. It has the L-brackets as you've described.

Both pictures are the same hitch, used on two different tow vehicles.

If you look closely, the drawbar is upside down, with the extra holes at the bottom in the first pic, versus at the top in the first pic.

The instructions are here: Equalizer Instructions.
kamperdog
Explorer
Apr 29, 2015
Thanks everyone. I have about 2 months to do it, but i also want time to test it at least once.
skipnchar
Explorer
Apr 29, 2015
Ball height is best determined by how the trailer tows. Should be close to level for best performance and stability. Many WD hitches come with an adjustable height ball mount so you can achieve the proper height and these will work either way you flip them but again, based on your need to get a near level tow.
Good luck / Skip
kamperdog
Explorer
Apr 29, 2015
Theres a big RV place pretty close but. Im sure they would charge an arm and leg though. Thats why Im asking if it can be done myself.