Now's your chance to pickup one of the best values around in a 3500 watt generator. The https://www.harborfreight.com/3500-watt-super-quiet-inverter-generator-63584.html just went on sale for $799.99
Some of its robust features are:
I just purchased the Champion 3400 for $989.99. I liked it's built in duel fuel capability. Of course, after the fact I stumble across a YouTube video showing how to add that mod to the Predator. Note that there are more than one videos for this conversion. Find one that matches your learning style.
Some of its robust features are:
- 11 Hour Runtime
- Super Quiet @ 57db
- Electric Start
I just purchased the Champion 3400 for $989.99. I liked it's built in duel fuel capability. Of course, after the fact I stumble across a YouTube video showing how to add that mod to the Predator. Note that there are more than one videos for this conversion. Find one that matches your learning style.
I decided to add a couple of photos of my Gen transfer panel..
I added digital Volt and ammeters on the left side so I can monitor the gen voltage and current. One meter for each leg..
Inside the door, the top breakers which in this panel are opposing left breaker is from gen and right breaker is feed from main panel.
The two breakers are held together by a retainer under the panel front.
There is a metal strap which fits under the panel front and fits the channel between the breakers and comes up to the breaker handles and a pin drops through the breaker handles tying the two breaker handles together loosely. There has to be enough slop to allow breakers to trip but not to much so when you push one breaker on the opposite breaker flips off.
Neat, simple yet very effective.
I started out with a smaller gen panel but it didn't have enough circuits.. So, I was able to use the parts from the small panel and moved them to a bigger panel with same breaker layout so that panel in the pix was a $60 panel without a main breaker.. And yeah, the gen has a 60A breaker on a gen that only can supply 30A.. I used what I had at the time but keeping in mind the gen HAS built in 30A breakers so the wiring and gen is safe.. Only using that breaker as a switch in this case.
I added digital Volt and ammeters on the left side so I can monitor the gen voltage and current. One meter for each leg..
Inside the door, the top breakers which in this panel are opposing left breaker is from gen and right breaker is feed from main panel.
The two breakers are held together by a retainer under the panel front.
There is a metal strap which fits under the panel front and fits the channel between the breakers and comes up to the breaker handles and a pin drops through the breaker handles tying the two breaker handles together loosely. There has to be enough slop to allow breakers to trip but not to much so when you push one breaker on the opposite breaker flips off.
Neat, simple yet very effective.
I started out with a smaller gen panel but it didn't have enough circuits.. So, I was able to use the parts from the small panel and moved them to a bigger panel with same breaker layout so that panel in the pix was a $60 panel without a main breaker.. And yeah, the gen has a 60A breaker on a gen that only can supply 30A.. I used what I had at the time but keeping in mind the gen HAS built in 30A breakers so the wiring and gen is safe.. Only using that breaker as a switch in this case.
Boon Docker wrote:
The transfer switch that I use when powering my house with a generator is the main 200 amp breaker, I just click it off. Works just fine.
Boon Docker,
Technically you are correct that ONCE you turn off the Breaker panel MAIN breaker then no "backfeed" will happen.
HOWEVER, the problem is that it is EASY to forget to do that step.
OTHERS in your family MAY/CAN/MOST LIKELY forget to do that step.
In an blackout situation you or your family will be stressed, trying to get some power quickly and doing this most likely in pitch black darkness with a couple of flashlights with near dead batteries.
That IS the cold hard reality and why folks get pretty riled up over this.
You also have to factor in the opposite can happen when the power comes back on and someone has forgotten to turn the main breaker off.. Now you have the power co feeding voltage back into YOUR precious gen.. IF you are lucky, it will simply trip your gens breaker.. If you are unlucky, it can damage/burn/break up your precious gen..
It is not the proper way to do this.
My Dad had done it your way 40 yrs ago, I watched him do that to feed a gen into our house during a week long power outage in the dead of winter. Yes, it worked but it was not the right way to do this.
Back then there was NO AFFORDABLE home or consumer gen transfer panels and you HAD to do what you had to do to make things work.
Now days, there are lots of AFFORDABLE methods to connect a gen to your home that are safe, does not require one to "remember" a switch sequence and automatically protects you, your generator and even the power company linesman.
Manual home transfer panels are cheap insurance and start out around $60-$200 depending on gen size and qty of priority circuits.
Modern days, NEC has recognized then need for safely interfacing home gens to the home panel, they have gone out of their way to approve breaker panel breaker INTERLOCKS for this purpose.
There are now a vast variety of Interlock kits available for many breaker panels and they start out around $60..
Interlocks are a great way to make this very safe, you basically add a dedicated breaker to your panel for your gen, add the Interlock kit to the breaker panel.
Here is an example..
Interlock HERE $69
INTERLOCK HERE for $56
Those are just a couple of examples, not all that difficult to install or expensive..
The interlock blocks the gen breaker from being turned on while the main breaker is on.
When the main breaker is turned off the Interlock will now unblock the Gen breaker..
There is zero ways both gen and main can be on at the same time basically turning your panel into a gen transfer panel.
It is a low cost, safe and effective way to do this properly.
Boon Docker, I ask that perhaps you might consider adding a Interlock to your setup?
Even though my Dad may have done it your way, myself, I HAVE installed a manual transfer panel to my home and have moved my priority circuits to that panel.
Yes, I had some expense by doing it the right way, but I can relax and know that if I am not at home, my family can quickly and safely get the gen up and running or at least there is one less thing for myself to do to keep me and my family safe.
