cancel
Showing results for 
Search instead for 
Did you mean: 

That Burning Smell

AllegroD
Nomad
Nomad
Well, at about 2 AM we woke up to an awful "ozone" electrical burning smell. We could not locate the source. The smell returned at about 0900. Again, we could not find the source. We thought maybe the electric WH. Since we were leaving soon and the weather was fair, we just unplugged. When we got home, we did not plug back in.

Well, after some searching we found this:

and this:


It is in the shop now for replacing.
17 REPLIES 17

AllegroD
Nomad
Nomad
This is the front side, so you can see the input. Sorry it took a couple days.

down_home
Explorer II
Explorer II
Loose connections and low voltage high amp. Only time we've seen it is at the tower plug in. We were using a 30 amp pigtail adapter.The gauge in the house showed 105 volts or less. We had surge low voltage protector plus built in same.
I cut the gen on which broke the circuit to the tower, quickest way, I thought.
When I unplugged the cord it was melting and burned my hand.
I had cleaned the plug with contact cleaner before we hooked up to the tower.
Park had problems or maybe just the tower. We just used the generator the rest of the evening. We left in the morning not having to fool with unhooking in the am or take boards from under the jacks, since it was paved. This is the way RVing should be. 🙂

MEXICOWANDERER
Explorer
Explorer
I don't mean to spook anyone but actual fire is not the only thing that should be an issue.

The plethora of plastic in an RV lends itself to toxic smoldering that can kill even though there is no actual flame.

And through a confluence of error it is possible to create a short circuit in the shore power line that passes up the cord, into the rig and exits via the green ground circuit.

With absolutely no safety current limit.

Quicksilver has a marine 30-amp breaker on the neutral but this absolutely cannot be done with a 50-amp 240 volt system.

AllegroD
Nomad
Nomad
Boomerweps wrote:
What was the breaker feeding?


The whole panel. These are the input (incoming) 50amp breakers.

BTW, I did not post. This is on a 2013 Tiffin 36LA.

MEXICOWANDERER
Explorer
Explorer
You would be surprised what DeOxit D100 does for tight fitting but slight heating of blade type conventional breakers under load. Too many times I have treated the blades and the heat slumped to normal. This is no gimmick fix.

Same for tubular aluminum barrel soldering guns -- Weller

Remove tip. Scratch up the inside of the aluminum barrel. SOLDER the tip ends that fit into the barrels. Saturate with D100 then instead of lasting so many months the tips have lasted me for YEARS without having to remove them and clean the aluminum barrel again.

time2roll
Nomad
Nomad
Have had similar with stationary home systems. Had to replace all nine breaker panels with same issue.

dougrainer
Nomad
Nomad
It is caused by LOOSE connections in the RV breaker box. Either the neutral or HOT. Since the Black HOT and breaker burnt--it was loose BLACK wires in the breaker box. Doug

MEXICOWANDERER
Explorer
Explorer
Square D and Siemens type house breakers were never designed to go thumping down the interstate


But these breakers are.



Screws with lockwashers...

sparkydave
Explorer
Explorer
Yes, it happens. Just had to replace the service panel in my 1970s house because the bus bar corroded, and the fingers on the breakers were starting to arc and burn. Most notably on the electric dryer breaker and air conditioning breaker.

BB_TX
Nomad
Nomad
It happens. Mother-in-law had to have the distribution panel in her house replaced due to a burned breaker and buss.

Boomerweps
Explorer
Explorer
What was the breaker feeding?
2019 Wolf Pup 16 BHS Limited, axle flipped
2019 F150 4x4 SCrew SB STX 5.0 3.55 factory tow package, 7000#GVWR, 1990 CC Tow mirrors, ITBC, SumoSprings,

Dusty_R
Explorer
Explorer
I replaced a 42 pole panel in a shop once where they were turning the lights on and off using the breakers. That caused the breakers to wear from the everyday movement.

wa8yxm
Explorer III
Explorer III
Have never seen that IN A MOTOR HOME or house.. HAVE however seen it. Reported it to park maintenance.. They came out with a new breaker and fixed it. (Well I detected it by other means but SAW it when the park handy-person opened the box. I mean I do not apply screwdriver to park hardware.. Just fingers).
Home was where I park it. but alas the.
2005 Damon Intruder 377 Alas declared a total loss
after a semi "nicked" it. Still have the radios
Kenwood TS-2000, ICOM ID-5100, ID-51A+2, ID-880 REF030C most times

TenOC
Nomad
Nomad
Yes, circuit breakers go bad most of the time due to poor electrical connections. They do make an anti-oxid grease that may (?) help.
Please give me enough troubles, uncertainty, problems, obstacles and STRESS so that I do not become arrogant, proud, and smug in my own abilities, and enough blessings and good times that I realize that someone else is in charge of my life.

Travel Photos