Hitch Installation

Bedlam wrote:
Just the Curt adapter plate alone costs almost as much as the entire Andersen Ultimate setup. I didn't price the B&W Turnover since I thought it would not work with a round shank.

This is not some thing I need right now, but it can be something I can look for used or pick up at discount if I know what fits.

That price is Canadian dollars, I'm positive its a heck of a lot cheaper below the 49th.


LOL - oops I just looked at Curt site... not much difference in price, unless you bought up here at $.75US/Cdn dollar... 25% cheaper... :)

Ok, searched again... Etrailers - http://www.etrailer.com/s.aspx?qry=curt+adapters much better price! And free shipping if your in the US.

Just the Curt adapter plate alone costs almost as much as the entire Andersen Ultimate setup. I didn't price the B&W Turnover since I thought it would not work with a round shank.

This is not some thing I need right now, but it can be something I can look for used or pick up at discount if I know what fits.

Bedlam wrote:
I have a Curt 30k lb drop in ball gooseneck - Does anyone know if these adapters work with it too?

http://www.curtmfg.com/Category/65/Double%20Lock?page=1

I didn't understand the Anderson adapter from the pictures I saw on their site until I visited eTrailer to see how that block turns the pin into a ball socket:

https://www.etrailer.com/Gooseneck-and-Fifth-Wheel-Adapters/Andersen/AM3225.html

Or you could use one of these:

http://www.hitchwarehouse.com/store/product/21826/Curt-X5-5th-Wheel-Adapter-Plate-16310/

Depending if your using B&W with the "square" shank ball or the Reese "round" shank ball. They have adapters for either.

Charley67 wrote:
I have the B&W turnover ball, and thanks to the good advice of you guys, my new B&W Companion hitch will be here Monday morning. I would not have known about this without you. Two RV dealers have tried to sell me gooseneck adapters, which I just didn't feel good about.

Very good! B&W makes a great hitch.
I'd also steer clear of the dealers who tried pushing the adapters on you. They may well work for some, but not at all the best choice.

I have the B&W turnover ball, and thanks to the good advice of you guys, my new B&W Companion hitch will be here Monday morning. I would not have known about this without you. Two RV dealers have tried to sell me gooseneck adapters, which I just didn't feel good about.

Greene728 wrote:
Use the gooseneck hitch you already have instead of taking it out and then turning around and installing bed rails. Check out the highly recommended B&W Companion or the Anderson Ultimate. Both utilize your existing gooseneck for 5th wheel hitches. Then when removed there is nothing intruding on your bed space.

X2 with the B&W

FYI: It appears that the B&W uses a square hole and Curt uses a round hole for their gooseneck balls. You can not mix and match their gooseneck accessories or adapters because of this difference.

Thanks, I didn't watch video but found better pictures on eTrailer. I was scratching my head trying to figure out how the pin attached and what was the purpose of the block with the release cable. Curt has something similar, but does not look as nice as the B&W or Anderson.

Bedlam wrote:
I have a Curt 30k lb drop in ball gooseneck - Does anyone know if these work with it? I don't understand the Anderson adapter from the pictures I see - it does not look like it has a saddle for a pin?

Take it one step further and view the videos.

The Anderson hitch has an adapter block that installs over the kingpin on the trailer, which allows it to hitch to the raised ball on the Anderson frame.

There is no actual 5th wheel with the Anderson hitch. It becomes a modified gooseneck.

The reason the Anderson hitch is okay, but a gooseneck adapter is not, is because the gooseneck adapter attaches to the pinbox on the trailer. This moves the pull point over a foot away from where it was designed, and puts extra stress on the trailer's pinbox.

Think of it like putting a cheater pipe on a wrench. If you've ever done that you know it works *most* of the time. Sometimes you break the wrench. Sometimes you bend it.



The Anderson hitch raises the gooseneck ball up to the pinbox, so the stresses are about the same vs. a true 5th wheel.

I have a Curt 30k lb drop in ball gooseneck - Does anyone know if these adapters work with it too?

http://www.curtmfg.com/Category/65/Double%20Lock?page=1

I didn't understand the Anderson adapter from the pictures I saw on their site until I visited eTrailer to see how that block turns the pin into a ball socket:

https://www.etrailer.com/Gooseneck-and-Fifth-Wheel-Adapters/Andersen/AM3225.html