All ActivityMost RecentMost LikesSolutionsRe: I-70 St.Louis to Kansas City & beyond ?I think that US-36 across Kansas is a lot smoother road than I-70. I like to get off the interstate and see a little more.Re: Onan 4000 Microquiet not startingJust a "clicking" noise but won't turn over. (that click is probably the sound of the starter motor running the starter Bendix ( gear on starter motor) into the gear on the flywheel on generator motor This could be the sign of a low battery or bad cable connections with the resulting “stuck starter”. I had a similar problem with my generator. I checked it before a trip to Alaska and all appeared to be fine. Used it a couple of times on the trip and then it wouldn't start. It got to the point that it wouldn't turn over and just made a click (klunk) that sounded as if the starter was jammed. After returning home, I found information this forum that explained that sometimes the piston in the engine could stop near the top of the compression stroke and the starter motor then could not turn the engine over. The solution was to turn the engine over by hand so it was past the top of the compression stroke. I found that by putting a wrench on the nut on the flywheel, I could get the engine rotated past the compression stroke. I also discovered that I was getting a big drop in the 12 volts as I tried to start the generator. As a test, I used jumper cables from my truck directly to the generator (negative to generator frame – positive to battery side of starter solenoid) and it started instantly. (after resolving the stuck starter by turning the engine over by hand) In my RV, the frame was used for the negative wire and the connections from the frame to the generator had corroded and although I could get a 12-volt measurement, the corroded connections would not allow enough current to pass to run the starter. In addition to replacing the corroded connectors, I ran a heavy gauge copper wire from the battery ground to the starter ground. This solved my problems. As stated above, a large drop in voltage when trying to run the starter indicates a bad connection. You might need to check ALL of your ground connections from the generator all the way back to the batteries. A bad electrical connection increases the resistance in a circuit. Ohm’s Law states E=IR where E = voltage I = current and r = resistance ---- Since the battery voltage will not increase (it actually decreases with each attempted start), increased resistance causes a decrease in current. With a decrease in current, the starter motor produces less torque (turning effect) because the magnetic field produced in the starter is proportional to the current. When the piston in the motor’s cylinder goes upward during the compression stroke the volume of the area from the top of the piston to the bottom of the cylinder head becomes less, According to Boyle's law, if you reduce the volume of a quantity of gas, the pressure will increase. When the force of the gas pushing down on the piston (pressure) equals the torque of the starter the starter motor stops turning. Attempted restarting does nothing to change these forces and the starter motor in an attempt to turn, just runs the starter bendix into the flywheel producing the clicking sound. By physically turning the motor past top dead center, by pulling on flywheel or placing a wrench on the flywheel nut, the piston starts on its downward stroke and the pressure becomes less so that the torque of the starter is adequate to rotate the motor.Re: BAY OF FUNDYThe tides in the Bay of Fundy are most impressive, something that we don’t get to see in the Midwest. Nova Scotia and the Bay of Fundy have some of the highest tides in the world and something that I think is very interesting to observe. I was able to see a 48 foot tide. Another tidal phenomenon is the tidal bore where rivers actually change direction as a wave front moves up the river. There is a Tidal Bore at Truro Nova Scotia where you can watch a wave come up the river and the river flow change directions. There are several factors that influence the tides but in simplified terms, and highest high tide and lowest low tide occur on the same day and that occurs on or about the new and full moon phases. Two weeks later, during the first or third quarter phases, the tidal range is the lowest--- lowest high tide and highest low tide. With basically two high and two low tides a day your viewing time needs to be over six hours for a complete transition. Find a dock where there will be a big change in the tide and stay there for at least six hours to watch the water level change. There is such a dock near Blomidon Provincial park. It is fun to watch the boats go from dock level to resting on the muddy bottom with their decks many feet (10-20) below the dock. The Bay of Fundy is certainly more impressive during times of greatest tidal range. I always tried to plan my Nova Scotia trips based upon the tide tables. If you still in the planning stages, try to be in Nova Scotia during a Full moon or a New moon to get the tides of highest range. Link to Tide TablesRe: campground around KC MissoouriJackson county parks Worlds of FunRe: Trout fishing in CO in July/AugustThe Yampa river goes right through this campground. Steamboat Campground
GroupsBucket List Trips Bucketlist destinations you just can't miss. Which spots stick with you?Jan 18, 202513,487 Posts
Bucket List Trips Bucketlist destinations you just can't miss. Which spots stick with you?Jan 18, 202513,487 Posts