Forum Discussion
1,450 Replies
- mwebber78ExplorerGo find a local dealer and buy a role of Eternabond before the rain. Prep the surface, apply, roll and forget it for the rest of your natural life.
- eaherrmannExplorer
L&MMusic wrote:
Argh!!!!! He did it again! While circling the block to gain access to the diesel pump at a gas station on our way to Houston, he did very well concentrating on the width of the rig. However, he neglacted to monitor the height and ripped the side of the roof again with the trees! We got the gas and drove a couple miles to an empty parking lot. He offered to do it, but I got up on the roof, cleaned the surfaces around the 11 or so nicks and rips and covered them with duct tape. I sure hope I got them all. We arrived at the campground around 6:00, and the duct tape looks like it's holding, but it's supposed to rain a lot in the next couple days. I'll be heading to Home Depot to get tarp and bricks to provide additional coverage. There's also gotta be a way to make that stuff stronger and rip resistant!! How about many layers of patching?
Congrats, Just campin. Careful driving out there!
Sorry to say, we felt your pain. (Hit an oak tree at 3am)We used a tarp and duct tape as a temporary fix until we got to a RV shop. We followed the tech's suggestions and it lasted 3+ weeks while traveling from Miami to DC and then some. We then had to have the front repaired and a new roof installed.
--Clean with spic and span and dry.
--Use the roof sealant over rip plus at least 1 inch.
--We had a large hole so we cleaned and taped over with white duct tape then applied sealant. Worked well and didn't look so bad either. Thank goodness we have great insurance. They paid for the roof and the front side I scraped up getting out of the mess that ripped up the roof. Why do lessons have to cost so much? And yes, we now carry all of the above suggested materials :( - CHV_FRKExplorer
L&MMusic wrote:
Argh!!!!! He did it again! While circling the block to gain access to the diesel pump at a gas station on our way to Houston, he did very well concentrating on the width of the rig. However, he neglacted to monitor the height and ripped the side of the roof again with the trees! We got the gas and drove a couple miles to an empty parking lot. He offered to do it, but I got up on the roof, cleaned the surfaces around the 11 or so nicks and rips and covered them with duct tape. I sure hope I got them all. We arrived at the campground around 6:00, and the duct tape looks like it's holding, but it's supposed to rain a lot in the next couple days. I'll be heading to Home Depot to get tarp and bricks to provide additional coverage. There's also gotta be a way to make that stuff stronger and rip resistant!! How about many layers of patching?
Congrats, Just campin. Careful driving out there!
I think you two need to carry some eternabond with you! - L_MMusicExplorerArgh!!!!! He did it again! While circling the block to gain access to the diesel pump at a gas station on our way to Houston, he did very well concentrating on the width of the rig. However, he neglacted to monitor the height and ripped the side of the roof again with the trees! We got the gas and drove a couple miles to an empty parking lot. He offered to do it, but I got up on the roof, cleaned the surfaces around the 11 or so nicks and rips and covered them with duct tape. I sure hope I got them all. We arrived at the campground around 6:00, and the duct tape looks like it's holding, but it's supposed to rain a lot in the next couple days. I'll be heading to Home Depot to get tarp and bricks to provide additional coverage. There's also gotta be a way to make that stuff stronger and rip resistant!! How about many layers of patching?
Congrats, Just campin. Careful driving out there! - M_GO_BLUE1Explorer
loydt wrote:
^we just removed it. we have a large cutting block that sits on top of the stove top. To keep it from sliding off we put a piece of thet rubber type shelf liner under it. Works great.
That's an idea Loyd...thanks! I'll suggest this option to the wife...
Waiting to hear what Jayco says then will suggest the cutting board idea...all depends what Jayco wants for something like that to be made... - loydtExplorer^we just removed it. we have a large cutting block that sits on top of the stove top. To keep it from sliding off we put a piece of thet rubber type shelf liner under it. Works great.
- M_GO_BLUE1ExplorerOk folks...contacted Jayco after seeing the 2010 version of the 35RLTS...
Asking Jayco if it is possible to buy a new folding cover (the one that folds over the burners on the stove)...would like to get a folding cover made that is of the same material as our countertops (can only look better than that dull looking black metal folding cover)... - petekerwienExplorerJust Camping- great news, show us some pictures.
- Just_campinExplorerWell, I joined the Designer club, I got a 2010 Designer 35rlts from RV Direct, picked it up in Des Moines,two weeks ago , took it out to Stillwater OK. last week no problems
- 2QAYLExplorer
cruz wrote:
Tried beach balls and they worked pretty good for the flapping ... but lost 2 of them when they blew away in some really heavy wind.
CRUZ
Not to be critical of the beach ball idea but it does seem to me that the time one might want them the most would be in a really heavy wind!
On the other hand it doesn't sound to me like CRUZ's system would be much fun at the beach. Struts for the drawbridge across the sandcastle moat maybe??:B:B:B I think I'd sooner have the ball.
Cheers,
Dave
About Fifth Wheel Group
19,032 PostsLatest Activity: Jan 04, 2026