So I've had all the parts for a few weeks now and decided today after I cut the grass I'd go ahead and give one wheel a try. I bought a 20 ton bottle jack ( recommended by someone here ) it worked great!! I had a grease gun, bearing packer, new bearings, seals and races. I also went to harbor freight and bought a race insert kit for like $25.00 and that was a life saver by itself. I guess the hardest part was getting the old races out but even that wasn't too bad. The bearings, seals and races were pretty cheap so I just replaced everything. I won't say how long it's been since the bearings had been looked at. The old grease looked ok to me but those bearings were 8 years old and cheap to replace so it's all new now. Also adjusted the brakes while I had the wheel off the ground...... The wheel was spinning very free and with a little adjustment I had it making the swoosh swoosh sound. I was told to give it a little resistance, sound right???I guess all in all about 1.5 hours for that one wheel and the other three will go quicker now that I know what to expect.

Sounds like you did it right. Randu

I have Dexter axles and they say to torque the bearing nut to 50 ft lbs while turning the wheel, loosen the nut then only finger tighten. You may be a bit too tight if there is resistance. I'd google instructions from the axle manufacturer.That being said, congratulations on doing the job yourself. I do all the work on my vehicles myself. This saves me a ton of money and enables me to use superior parts.

jfkmk wrote:I have Dexter axles and they say to torque the bearing nut to 50 ft lbs while turning the wheel, loosen the nut then only finger tighten. You may be a bit too tight if there is resistance. I'd google instructions from the axle manufacturer.That being said, congratulations on doing the job yourself. I do all the work on my vehicles myself. This saves me a ton of money and enables me to use superior parts.But since you said you experienced a little resistance only after adjusting the brakes, I think your wheel bearing preload must be OK. But in case you are wondering, what jfkmk is right about setting bearing pre-load. 50 pounds while spinning. Back off. Finger tight. Insert cotter pin. Done.

Make sure your drift tool for removing the races left no burrs to prevent the race from setting square.

Nice work. You now have a skill that will save you a lot of money over shop fees. You'll know the job is done right instead of wondering how much experience the dealer mechanic has.

New Wheel Bearings Installed | Good Sam Community

Randu
Explorer
Jun 02, 2014
Sounds like you did it right.
Randu
jfkmk
Explorer
Jun 02, 2014
I have Dexter axles and they say to torque the bearing nut to 50 ft lbs while turning the wheel, loosen the nut then only finger tighten. You may be a bit too tight if there is resistance. I'd google instructions from the axle manufacturer.

That being said, congratulations on doing the job yourself. I do all the work on my vehicles myself. This saves me a ton of money and enables me to use superior parts.
Vulcaneer
Explorer
Jun 02, 2014
jfkmk wrote:
I have Dexter axles and they say to torque the bearing nut to 50 ft lbs while turning the wheel, loosen the nut then only finger tighten. You may be a bit too tight if there is resistance. I'd google instructions from the axle manufacturer.

That being said, congratulations on doing the job yourself. I do all the work on my vehicles myself. This saves me a ton of money and enables me to use superior parts.

But since you said you experienced a little resistance only after adjusting the brakes, I think your wheel bearing preload must be OK.

But in case you are wondering, what jfkmk is right about setting bearing pre-load. 50 pounds while spinning. Back off. Finger tight. Insert cotter pin. Done.
Charlie_D_
Explorer
Jun 02, 2014
Make sure your drift tool for removing the races left no burrs to prevent the race from setting square.
Peg_Leg
Explorer
Jun 02, 2014
Nice work. You now have a skill that will save you a lot of money over shop fees. You'll know the job is done right instead of wondering how much experience the dealer mechanic has.
abc40kids
Explorer
Jun 03, 2014
Peg Leg wrote:
Nice work. You now have a skill that will save you a lot of money over shop fees. You'll know the job is done right instead of wondering how much experience the dealer mechanic has.

Your right, the shop told me $600.00 to repack the bearings! Think I'm gonna pull the one wheel I did back off and check the castle nut to make sure it's not too tight. I don't think it is but at the same time I a previous poster said snug it up good to make sure it seats then back off..... I never really got it real tight and then backed off.
B_O__Plenty
Explorer II
Jun 03, 2014
$600.00!! That's insane.I would never go back there for anything...Should be $150.00-200.00..Where do these rip-off artists come from?

B.O.
abc40kids
Explorer
Jun 03, 2014
I would have given them $250.00 to repack them, I figured with them doing it all the time an hour or so per side, I'd even went $300.00 at the time.
aruba5er
Explorer
Jun 04, 2014
Shop labor here is charged at $95 an hour. By the time the mechanic gets the bearings, grease, jack etc around, gets it jacked up, wheels off and on and on you probably got3 hours for 4 wheels from start to finish including adjusting brakes, putting stuff away, etc . Not cheap. Thats why you have to learn how to do it yourself or have deep pockets. One of the biggest troubles I have in paying for labor is, did all that time charged go into MY repair or did someone interupt, chew the s**t, go to the bathroom, take a break, you know, ? Now how much time was really spent. $1.60 a minute adds up really fast. Would be better to get quote on how much the job costs and pay no more (flat rate)
Supreme_Oppress
Explorer
Jun 05, 2014
There is a certain satisfaction gained from doing a job yourself. You now know the condition of your brakes and bearings and can avoid worrying about them while on vacation. (Also, it's easier changing them in the driveway than on the side of a highway while wondering where to buy parts on a weekend.)

Forum Discussion

New Wheel Bearings Installed

About Fifth Wheel Group

Related Content

Wheel Bearings

wheel bearing

Re-pack wheel bearings

Front wheel bearing service timeline ??

5th wheel hitch installation