We will soon upgrade from a TT to a 5th Wheel, haven't purchased the 5th yet but know what make and model we will be buying, a Montana High Country, pic below of the front cap of that model. Our truck is a Ram Crew Cab with a 6'4" bed. I have an Andersen hitch which attaches to a GooseBall in the truck, pic below. With the offset of the Andersen hitch, it appears that the Andersen ball is just about centered over the truck axle. My questions are, do you think with the hitch as shown, and a 5th wheel with a front end as shown, can that work safely if very careful about backing up? My GooseNeck Hitch is a B&W. B&W sells a 4" offset ball, which would extend the hitch 4" to the rear. Would this be preferable? Is there any problems regarding the fifth wheel with moving the attachment point 4" rearward? And lastly, those with experience with the Andersen hitch, the 4" offset ball looks like it sits about 3/4" above the bed. When attaching the Andersen hitch, would I still be able to pull it down snug to the bed? Thanks in advance for any information or advice!

I am not an Andersen hitch owner, but do know that many use them with the Ram 6' 4" bed. The red coupler, that fastens to the pin, can be reversed, to allow more clearance. However, this may cause some issues, with certain pinboxes, hitting the bedrail of truck, at extreme turns.Bottom line...hitch will work, just need to learn limitations, BEFORE damage occurs.You will like the FW experience!Jerry

I have the same truck with the Andersen hitch , I use the adapter putting the fifth wheel closer to the cab ,no clearance problems . I had concerns with the pin box hitting the tailgate so the reason for the adapter in that position . Prior fifth wheel had the adapter the other way around putting it further from the cab ,no issues with that either . All depends on the pin box .Can't answer about the gooseneck connection ,I have the steel Andersen . It's mounted to the rail adapter attached to the puck system , its puts the ball slightly rear of axle center , so as far as the ball being back that's not a issue with towing . I have towed with the Andersen now for several years ,wouldn't tow with anything else .My son also tows with the Andersen , the aluminum like yours , short bed Superduty ,no issues .

F.Y.I. using an Andersen hitch with any Montana (or Keystone 5th wheel) will VOID your frame warranty. There is a letter from Keystone to that effect and while some will argue they can't do that, it isn't a battle most want to fight. That 3 year frame warranty is a valuable asset and given the occurrence of wall separation from the frame 9usually due to bad welds), is something to be protected.

I stayed at a campground on the Oregon coast and talked to a man with a dented cab and a shattered rear window in his Ram SB truck. His truck was a Platinum edition with air suspension and it was giving him problems as to ride height flexibility. By coincidence, he was towing a new Montana High Country with an AUH hitch. The pin box was biting chunks out of his tail gate, so he reversed something on the hitch. He happily towed the trailer for many thousand miles without issue.He pulled into a poor access gas station and decided to back out. He was backing tight and the truck went down a driveway dip. The front of the trailer leaned forward and took out his window. The Montana has tapered front corners, but it slopes forward quickly.The owner was from Minnesota and was very easy going regarding the incident (more so than I would have been). He blamed himself for getting flustered and losing his concentration. He really liked the hitch prior to the incident.On edit, this was 4 years ago and as I recall, the slope of the front cap looks different than in your picture. Maybe they reacted to an issue. I also believe he had a MorRyde pin box instead of RotoFlex which you will have to lock out.

Absolutely nothing to do with the hitch , and everything to do due with the fact it being a short bed ,and the circumstances . That would of happened with a conventional hitch , or a slider. About the only thing that would of saved him would have been a automatic sliding hitch ,or him being aware enough to slide back a sliding hitch if he had one . What he did was reverse the adapter on his pin box for the Andersen hitch ,I did the same with my present fifth wheel , it looked like I was going to make contact with my tailgate ,so like him I reversed the adapter . Unlike my prior Montana fifth wheel a Montana it did have the MorRyde pin box ,and had no problem with the adapter putting the pin box further back towards the tailgate . Present fifth wheel has the lippert pin box. It comes right back to situational awareness when towing with a short bed ,and nothing to do with an Andersen hitch .

Towing 5th with an Andersen Hitch in Short Bed Truck

alanmikkelsen
Explorer
Mar 10, 2023
Been towing for 50 years, mostly goosenecks. The Andersen Ultimate Hitch is the best fifth wheel hitch I've used. I have a 6.5' bed, with a fuel tank/tool box combo in the front so I use the 4" B&W offset ball with my AUH without any problem. I did have to get the short internal tube (see Andersen website) because of the increased height of the B&W extension. Pulls like a dream, no chucking at all.
crcr
Explorer
Jan 18, 2023
ZeeLet50 wrote:
When I had my GMC 2500 it had a 6'bed and I put the coupler in the position to allow more clearance between the trailer and the cab. I also had a low profile roll up bed cover. The bottom of the pin box on turns over 60 degrees would contact the bed cover track and damage it. I did raise the ball up one level and it still made some contact. The next season I got my GMC 3500 and it had a 6'5" bed so I turned the coupler around and have had no issues.
So be aware pushing the pin box back in the bed will also affect the clearance to the sides. Now if I did not have a bed cover rail there would of been no issue but its something to look out for. Now this was with the stock pin box. I did upgrade to the MorRyde cushioned pin box and it does have a different profile that may have solved my problem of contact but I upgraded with the new truck so I will never know. Anderson is great as its so light the wife can install it.

OK, thanks for that information. I happen to have a bed cover, folding, and both tracks attach to the inside of each side of the bed. I had not thought of the possibility of the back of the pinbox hitting the bed cover tracks on a turn, but I can see how that might be likely. It will be inconvenient, but I may remove my bed cover + tracks before towing a fifth wheel.

Word to the wise about leaving an Andersen hitch exposed when parking in public areas -- all thieves need is some sockets and a ratchet or maybe a crescent wrench to relieve you of your hitch. I know this does happen on occasion, as I was shopping for a used Andersen, found one for sale online without the coupler in the picture. I messaged the seller and asked if he had the coupler for it, and he said no. I replied, "Thanks, but I don't buy stolen goods." He did not reply at all, pretty much admitting it was stolen goods.
crcr
Explorer
Jan 18, 2023
cummins2014 wrote:
I would start with having the Andersen adapter putting the fifth wheel further from the cab of the truck . That’s the position I had it in with my first fifth wheel with the MorRyde pin box , no clearance problems with the tailgate , my present fifth , same truck I reversed the Anderson adapter putting the fifth wheel closer to the cab . I had concerns with the pin box making contact with the tailgate , this fifth wheel has the Lippert pin box . Either position I have had no problems with cab clearance , same truck as yours .

Thanks much. That has sounded like the most practical starting point for my equipment so most likely I will start there.
ZeeLet50
Explorer
Jan 18, 2023
When I had my GMC 2500 it had a 6'bed and I put the coupler in the position to allow more clearance between the trailer and the cab. I also had a low profile roll up bed cover. The bottom of the pin box on turns over 60 degrees would contact the bed cover track and damage it. I did raise the ball up one level and it still made some contact. The next season I got my GMC 3500 and it had a 6'5" bed so I turned the coupler around and have had no issues.
So be aware pushing the pin box back in the bed will also affect the clearance to the sides. Now if I did not have a bed cover rail there would of been no issue but its something to look out for. Now this was with the stock pin box. I did upgrade to the MorRyde cushioned pin box and it does have a different profile that may have solved my problem of contact but I upgraded with the new truck so I will never know. Anderson is great as its so light the wife can install it.
cummins2014
Explorer
Jan 17, 2023
crcr wrote:
ZeeLet50 wrote:
To answer the OP's initial question and not off topic like this has gone...the short bed will work with the Anderson hitch. It does require situational awareness as does any hitch. Take it too far and there can be damage. The Anderson pulls fine. Just be aware that any placement of the pin further back of the rear axle will affect the ride somewhat. So that offset ball pushing the pin further back will work but you might get more "chunking" or sag. And that will be with conventional or Anderson hitches. The only difference you can see between the Anderson and conventional setup to the trailer will be a conventional will have a larger contact area with the pin box. I dont see how this stresses the frame more. It could break the pin off of a badly welded pinbox but maybe there is something I am missing or its just CYA of the manufacture. The new Morryde pinboxes are much beefier than the standard pinbox that used to come on the pre 2019 models.

Thanks to the input in this thread, I don't expect to try to / need to use an offset gooseneck ball. It sounds like you have experience with the Andersen hitch, so I have a question, if I might, for you, or anyone else with experience with the Andersen. The ball on top of the Andersen hitch in my truck appears to sit pretty much right over the rear axle.

The Andersen coupler, as you know, is going to offset the kingpin a few inches to the front or rear from the Andersen ball. I understand that pinbox positioning and the front cap of fifth wheel campers vary. My question is, would you suggest I use the Andersen coupler to offset the kingpin to the front or rear of the Andersen ball? This would be a starting position and I would then tow and observe carefully, and if needed, switch the direction of the Andersen coupler.

I would start with having the Andersen adapter putting the fifth wheel further from the cab of the truck . That’s the position I had it in with my first fifth wheel with the MorRyde pin box , no clearance problems with the tailgate , my present fifth , same truck I reversed the Anderson adapter putting the fifth wheel closer to the cab . I had concerns with the pin box making contact with the tailgate , this fifth wheel has the Lippert pin box . Either position I have had no problems with cab clearance , same truck as yours .
crcr
Explorer
Jan 17, 2023
ZeeLet50 wrote:
To answer the OP's initial question and not off topic like this has gone...the short bed will work with the Anderson hitch. It does require situational awareness as does any hitch. Take it too far and there can be damage. The Anderson pulls fine. Just be aware that any placement of the pin further back of the rear axle will affect the ride somewhat. So that offset ball pushing the pin further back will work but you might get more "chunking" or sag. And that will be with conventional or Anderson hitches. The only difference you can see between the Anderson and conventional setup to the trailer will be a conventional will have a larger contact area with the pin box. I dont see how this stresses the frame more. It could break the pin off of a badly welded pinbox but maybe there is something I am missing or its just CYA of the manufacture. The new Morryde pinboxes are much beefier than the standard pinbox that used to come on the pre 2019 models.

Thanks to the input in this thread, I don't expect to try to / need to use an offset gooseneck ball. It sounds like you have experience with the Andersen hitch, so I have a question, if I might, for you, or anyone else with experience with the Andersen. The ball on top of the Andersen hitch in my truck appears to sit pretty much right over the rear axle.

The Andersen coupler, as you know, is going to offset the kingpin a few inches to the front or rear from the Andersen ball. I understand that pinbox positioning and the front cap of fifth wheel campers vary. My question is, would you suggest I use the Andersen coupler to offset the kingpin to the front or rear of the Andersen ball? This would be a starting position and I would then tow and observe carefully, and if needed, switch the direction of the Andersen coupler.
Cummins12V98
Explorer III
Jan 17, 2023
cummins2014 wrote:
Cummins12V98 wrote:
" Have had a turbo actuator go out on my 6.7 Cummins , many have not , many have . It’s well documented it’s a pretty common problem with 6.7 Cummins"

I have to ask, Turbo Charger or "ACTUATOR" ???

“ TURBO ACTUATOR “

YES the actuators do have a record of failing. Mine was replaced under warranty at around 90k.
crcr
Explorer
Jan 17, 2023
ZeeLet50 wrote:
To answer the OP's initial question and not off topic like this has gone...the short bed will work with the Anderson hitch. It does require situational awareness as does any hitch. Take it too far and there can be damage. The Anderson pulls fine. Just be aware that any placement of the pin further back of the rear axle will affect the ride somewhat. So that offset ball pushing the pin further back will work but you might get more "chunking" or sag. And that will be with conventional or Anderson hitches. The only difference you can see between the Anderson and conventional setup to the trailer will be a conventional will have a larger contact area with the pin box. I dont see how this stresses the frame more. It could break the pin off of a badly welded pinbox but maybe there is something I am missing or its just CYA of the manufacture. The new Morryde pinboxes are much beefier than the standard pinbox that used to come on the pre 2019 models.

OK, thanks for the tips and cautions on using the Andersen hitch, much appreciated.
cummins2014
Explorer
Jan 17, 2023
Cummins12V98 wrote:
" Have had a turbo actuator go out on my 6.7 Cummins , many have not , many have . It’s well documented it’s a pretty common problem with 6.7 Cummins"

I have to ask, Turbo Charger or "ACTUATOR" ???

“ TURBO ACTUATOR “
Cummins12V98
Explorer III
Jan 16, 2023
" Have had a turbo actuator go out on my 6.7 Cummins , many have not , many have . It’s well documented it’s a pretty common problem with 6.7 Cummins"

I have to ask, Turbo Charger or "ACTUATOR" ???

Forum Discussion

Towing 5th with an Andersen Hitch in Short Bed Truck

About Fifth Wheel Group

Related Content

Andersen Hitch Failure

Andersen Hitches

Safety Chains Andersen Hitch

Andersen Hitch issue

Andersen Hitch questions