Lesson learned lol

Dave H M wrote:

profdant139 wrote:
This may help in getting it started -- instead of holding it in your hand, hold it in a socket of the right size -- I think 1" and 1/16?? That enables you to keep the rod perfectly horizontal, which is not easy by hand alone.

And if the nut is too loose in the socket, put some masking tape on the nut so that the socket fits more tightly. As soon as the nut begins to thread into the hole, take the tape off the nut.

Hope this helps!!

Is the way i do it and I occasionally "clean" the threads with the tap. ;)

Heyyy, as long as it works, then all is well! I must have been holding my mouth wrong or something!
:B

Thomas, did you use the tap to cut new threads, or just to clean out the old ones? Thanks.

My buddy had the tap I needed. Worked like a charm. Again, thank you all so much.

Shwthomas1975 wrote:
You guys are awesome. A tap would definitely help. I’ll call local hardware store to see if they have it, if not order from amazon. Thanks for the link. Are they all the same size? 3/4” 14 npt? I use teflon tape with it usually. I have tried by hand, with socket, pliers etc. I can get it to the point where it’s stick hand tight. Barely on the threads but then just slips right off.

All with an anode rod are that size. Be very careful getting a tap started, you don't want to start a new thread or crooked thread.

joebedford wrote:
Better to use a thread chaser than a tap. You don't want to cut new threads.

You're pretty unlikely to cut much new thread. It becomes very hard to turn when it starts to cut. All you need to do is clean out the old threads.

You guys are awesome. A tap would definitely help. I’ll call local hardware store to see if they have it, if not order from amazon. Thanks for the link. Are they all the same size? 3/4” 14 npt? I use teflon tape with it usually. I have tried by hand, with socket, pliers etc. I can get it to the point where it’s stick hand tight. Barely on the threads but then just slips right off.

profdant139 wrote:
This may help in getting it started -- instead of holding it in your hand, hold it in a socket of the right size -- I think 1" and 1/16?? That enables you to keep the rod perfectly horizontal, which is not easy by hand alone.

And if the nut is too loose in the socket, put some masking tape on the nut so that the socket fits more tightly. As soon as the nut begins to thread into the hole, take the tape off the nut.

Hope this helps!!

That works well, I lay paper towel over the socket end and jam the nut in, if it is loose I just add more paper. Tearing away excess lets you see better. After getting a good start, I pull the socket off and the paper falls away.

Better to use a thread chaser than a tap. You don't want to cut new threads.

I don't know any better, and someone will probably tell me its wrong, and why I should not do it, but after winter, when getting started again, I wirebrush the threads well, and put on a good wrapping of plumbers teflon tape on the threads. I always think that it makes a better seal, without having to over tighten, and makes it easier to remove at the end of the season. Sure, the tape is not electrically conductive, but there is still lots of metal to metal contact, which may or may not be required. Anyway, it has worked for me for over 15 seasons so far, with no problems.

profdant139 wrote:
This may help in getting it started -- instead of holding it in your hand, hold it in a socket of the right size -- I think 1" and 1/16?? That enables you to keep the rod perfectly horizontal, which is not easy by hand alone.

And if the nut is too loose in the socket, put some masking tape on the nut so that the socket fits more tightly. As soon as the nut begins to thread into the hole, take the tape off the nut.

Hope this helps!!

Is the way i do it and I occasionally "clean" the threads with the tap. ;)