Putting on TST tire monitors

Ron3rd wrote:

peirek wrote:
Two years and no issues. I did install metal valve stems and installed the sensors before balancing the tires.

X2, make sure you go with metal valve stems. When I first bought mine, TST said you "can" use them on rubber stems if you want. But I found they wobble enough to eventually crack the valve stem due to the rotational forces going down the road. I took my new trailer down to Americas Tire and had the metal stems installed and the tires/wheels balanced at the same time.

x2 on the metal stems, even if not running sensors. I run metal stems on all of my vehicles and trailers.

sidney wrote:
Spoke with Mike at TST today. He recommended I try using a repeater... he was pretty confident the drop outs are due to range limitations.

We have 36' 5th wheel... apparently that's pushing it range wise.

I have a 26' TT and need a repeater. I think it has more to do with the construction of the trailer and the bed cap, blocking the signal. Be sure that you get the correct repeater, TST has two different types.

Spoke with Mike at TST today. He recommended I try using a repeater... he was pretty confident the drop outs are due to range limitations.

We have 36' 5th wheel... apparently that's pushing it range wise.

What model of TST sensor is everyone going with these days? I like the idea of the flow through ones for simplicity. However, I wonder if they work well with a dually. There might be a clearance problem on my truck.

93Cobra2771 wrote:

sidney wrote:

peirek wrote:

sidney wrote:
Has any else found that you need to be very careful not to over tighten the sensors? Mine seems to be very sensitive... I've had 2 sensors stop working after towing for a long while as the temperatures increased. I pulled over and loosened the sensor a bit... started driving again and the sensor came back online after about 15 minutes.

Which system are you using? I have not noticed this issue with the TST.

I have a TST 507 system... without the flow thru sensors.

I'm towing a 36' 5er... could it be an intermittent range problem?

How long since the batteries were replaced? I'm guessing the batteries are on the way out.

This was happening when the batteries were less than 6 months old.

sidney wrote:

peirek wrote:

sidney wrote:
Has any else found that you need to be very careful not to over tighten the sensors? Mine seems to be very sensitive... I've had 2 sensors stop working after towing for a long while as the temperatures increased. I pulled over and loosened the sensor a bit... started driving again and the sensor came back online after about 15 minutes.

Which system are you using? I have not noticed this issue with the TST.

I have a TST 507 system... without the flow thru sensors.

I'm towing a 36' 5er... could it be an intermittent range problem?

How long since the batteries were replaced? I'm guessing the batteries are on the way out.

peirek wrote:
Two years and no issues. I did install metal valve stems and installed the sensors before balancing the tires.

X2, make sure you go with metal valve stems. When I first bought mine, TST said you "can" use them on rubber stems if you want. But I found they wobble enough to eventually crack the valve stem due to the rotational forces going down the road. I took my new trailer down to Americas Tire and had the metal stems installed and the tires/wheels balanced at the same time.

peirek wrote:

sidney wrote:
Has any else found that you need to be very careful not to over tighten the sensors? Mine seems to be very sensitive... I've had 2 sensors stop working after towing for a long while as the temperatures increased. I pulled over and loosened the sensor a bit... started driving again and the sensor came back online after about 15 minutes.

Which system are you using? I have not noticed this issue with the TST.

I have a TST 507 system... without the flow thru sensors.

I'm towing a 36' 5er... could it be an intermittent range problem?

sidney wrote:
Has any else found that you need to be very careful not to over tighten the sensors? Mine seems to be very sensitive... I've had 2 sensors stop working after towing for a long while as the temperatures increased. I pulled over and loosened the sensor a bit... started driving again and the sensor came back online after about 15 minutes.

Which system are you using? I have not noticed this issue with the TST.

Has any else found that you need to be very careful not to over tighten the sensors? Mine seems to be very sensitive... I've had 2 sensors stop working after towing for a long while as the temperatures increased. I pulled over and loosened the sensor a bit... started driving again and the sensor came back online after about 15 minutes.