Macerater pump electric lines

mbopp wrote:
If you're pumping a long distance use lots of water in the black tank. I started pumping some "sludge" and the pump was working so hard I thought it would quit. I used the back-flush valve & added more water to the tank through that.

Use lots of water in the black tank under any and all circumstances. That is what flushes (please pardon the pun) the solids out of the black tank in the first place.

If you're pumping a long distance use lots of water in the black tank. I started pumping some "sludge" and the pump was working so hard I thought it would quit. I used the back-flush valve & added more water to the tank through that.

Boomerweps wrote:
Yes, it's a FlowJet.
Next, what size hose are you using for discharge and how far do you normally pump?
I expect I should get 3/4", maybe 1". I'm looking at 100' or slightly more to my sewer cleanout from my preferred TT home parking spot. Very slightly downhill.

I have 75' of 3/4" hose, and my run is dead level. Downhill will help.

Boomerweps wrote:
Yes, it's a FlowJet.
Next, what size hose are you using for discharge and how far do you normally pump?
I expect I should get 3/4", maybe 1". I'm looking at 100' or slightly more to my sewer cleanout from my preferred TT home parking spot. Very slightly downhill.

50' max of 3/4" hose is recommended by the FloJet manufacturer.

Yes, it's a FlowJet.
Next, what size hose are you using for discharge and how far do you normally pump?
I expect I should get 3/4", maybe 1". I'm looking at 100' or slightly more to my sewer cleanout from my preferred TT home parking spot. Very slightly downhill.

Bobbo wrote:

SoundGuy wrote:

Bobbo wrote:
I ran 10g wire from the battery + and - terminals. I fused the + wire at 20 amps.

The OP hasn't specified just which macerator he's getting but if it's the popular FloJet waste macerator the line feeding it power doesn't need to be separately fused as there's a 20 amp fuse in the macerator's switch handle.

True, but I never run a long wire from the battery to anywhere without fusing it at the battery end.

Good practice. I'd bet a short in a 20' wire connected to battery would be a smoking, melting mess.
I started using these type of fuses to connect to battery terminals. They accept a 5/16" bolt so a user can bolt the fuse to a battery terminal and use a 5/16" ring terminal with a bolt in the other end of the fuse to connect the (+) wire.

SoundGuy wrote:

Bobbo wrote:
I ran 10g wire from the battery + and - terminals. I fused the + wire at 20 amps.

The OP hasn't specified just which macerator he's getting but if it's the popular FloJet waste macerator the line feeding it power doesn't need to be separately fused as there's a 20 amp fuse in the macerator's switch handle.

True, but I never run a long wire from the battery to anywhere without fusing it at the battery end.

Bobbo wrote:
I ran 10g wire from the battery + and - terminals. I fused the + wire at 20 amps.

The OP hasn't specified just which macerator he's getting but if it's the popular FloJet waste macerator the line feeding it power doesn't need to be separately fused as there's a 20 amp fuse in the macerator's switch handle.

I just take one of those little 7Ah batteries used for all sorts of stuff and place it in the compartment where the black and gray valves are. Then I run my grinder off of that. When the battery starts getting weak, I recharge it on the bench at home. I get 2 or 3 uses out of a fully charged battery.

1' to 10' power supply run ....12 ga wire

10' to 20' power supply run....10 ga wire

20A circuit

On my 5th wheel I ran POS/NEG wires from front compartment battery to roadside side compartment terminating at a PowerPole connector.
Changed out portable macerator pump connector and VIAIR compressor connector to PowerPole

For curbside power to use VIAIR compressor I have a 12V extension cord