Pioneer 19t4 TT water tank problem

If you are reading the water level by using the lights they ate notoriously inaccurate.

I thought about that. I cleaned the contacts at the tank and still the same. when I drain the tank at the 1/3 level it's real close to 15-16 gals.

Is it possible that the pickup has a hose in the tank and the end has curled so it is a few inches above the bottom of the tank?

If the outlet is on the side of the tank that is the problem. The pump will suck air when the water drops to the top of the fitting. Maybe you can tee into the tank drain.

Boband4 wrote:
Is it possible that the pickup has a hose in the tank and the end has curled so it is a few inches above the bottom of the tank?

Thats what I'm thinking. I just don't understand how that could happen after 8 0r 9 years of operating rather well. Also it would seem that there is no access to the pickup tube inside the tank, is that correct? If there is, where would it be located?
Thanks Sheps.

Lynnmor wrote:
If the outlet is on the side of the tank that is the problem. The pump will suck air when the water drops to the top of the fitting. Maybe you can tee into the tank drain.

The outlet is on the side at the very upper front road side corner of the tank. That seem like it would require a pickup tube inside the tank that extends to the bottom of the tank.
I like the idea of teeing off of the drain. Just a few fittings and some hose and a plug for the top fitting. I would have to route the hose back up through the floor to the pump. Mabe run hard pipe to above the frame or the floor, then change to the hose. I guess for protection, then seal the new floor entry.
Do you think the pump will pull water this extra distance? It's a Surflo pump I believe.

Sheps wrote:

Lynnmor wrote:
If the outlet is on the side of the tank that is the problem. The pump will suck air when the water drops to the top of the fitting. Maybe you can tee into the tank drain.

The outlet is on the side at the very upper front road side corner of the tank. That seem like it would require a pickup tube inside the tank that extends to the bottom of the tank.
I like the idea of teeing off of the drain. Just a few fittings and some hose and a plug for the top fitting. I would have to route the hose back up through the floor to the pump. Mabe run hard pipe to above the frame or the floor, then change to the hose. I guess for protection, then seal the new floor entry.
Do you think the pump will pull water this extra distance? It's a Surflo pump I believe.

There is no problem with the pump pulling it. I do think that the pipe at the top is just a vent, don't know. Can you trace that line and see where it goes?

Lynnmor wrote:

Sheps wrote:

Lynnmor wrote:
If the outlet is on the side of the tank that is the problem. The pump will suck air when the water drops to the top of the fitting. Maybe you can tee into the tank drain.

The outlet is on the side at the very upper front road side corner of the tank. That seem like it would require a pickup tube inside the tank that extends to the bottom of the tank.
I like the idea of teeing off of the drain. Just a few fittings and some hose and a plug for the top fitting. I would have to route the hose back up through the floor to the pump. Mabe run hard pipe to above the frame or the floor, then change to the hose. I guess for protection, then seal the new floor entry.
Do you think the pump will pull water this extra distance? It's a Surflo pump I believe.

There is no problem with the pump pulling it. I do think that the pipe at the top is just a vent, don't know. Can you trace that line and see where it goes?

My Pioneer has the same tank scenario, and has the same problem. I think I may have caused mine when I added a tank heater and insulation to mine. I too am considering tapping off the drain location. These tanks are easy to remove and reinstall, at least in these Pioneers.

I guess you could also install a screw out deck plate into the top of the tank near the outlet and see what's going on.
Link

Lynnmor wrote:

Sheps wrote:

Lynnmor wrote:
If the outlet is on the side of the tank that is the problem. The pump will suck air when the water drops to the top of the fitting. Maybe you can tee into the tank drain.

The outlet is on the side at the very upper front road side corner of the tank. That seem like it would require a pickup tube inside the tank that extends to the bottom of the tank.
I like the idea of teeing off of the drain. Just a few fittings and some hose and a plug for the top fitting. I would have to route the hose back up through the floor to the pump. Mabe run hard pipe to above the frame or the floor, then change to the hose. I guess for protection, then seal the new floor entry.
Do you think the pump will pull water this extra distance? It's a Surflo pump I believe.

There is no problem with the pump pulling it. I do think that the pipe at the top is just a vent, don't know. Can you trace that line and see where it goes?

There is a 1/2" pipe x 1/2 hose barb fitting in it and the pump hose connects to the fitting to pull water from the tank.