Torklift Tie Downs - Install

The Torklift site has section with all the installation manuals in PDF, but it requires a login provided by the company. These manuals have color pictures that can be scaled to get better views. This helped me when I was fitting my SuperHitch Magnum to my new RAM 5500. That may have helped you with your installation too. I like the fact that most of their products do not require drilling or modification of your truck.

Torklift makes good stuff. Nice write-up

I have used Torklift tie downs since 2005. I found them to be easy to install as long as the installer understands how to use the fishing tool. No issues in ten years with a 4000 pound camper. The rear right does get close to the exhaust and the sticker/placard came off quickly under use from exhaust heat. If you are impressed with the product, I would suggest you spell their name correctly.

Had HappiJacs prior, Torklifts are substantially stronger, no holes drilled into the bed, and it really mounts to the frame.

Bedlam wrote:
The Torklift site has section with all the installation manuals in PDF, but it requires a login provided by the company. These manuals have color pictures that can be scaled to get better views. This helped me when I was fitting my SuperHitch Magnum to my new RAM 5500. That may have helped you with your installation too. I like the fact that most of their products do not require drilling or modification of your truck.

wonder why they didn't tell me that when I was on the phone with them.

You should have looked at Happyjac website and checked the comparison of the 2 types of tie downs, according to HJ the fulcrum points are much better with HJ

I too have used both HJ's and TL, and prefer the TL by far. Didn't like the flimsiness of the HJ on the thin sheet metal at the front of the bed. I had bars mounted into my stock hitch for the rear so I have no experience with those silly bumper tab attachments.

I felt that for my model the instruction manual was very difficult to follow, pictures were not in order as far as I could tell, and they were hard to see. I wish they could have color pictures.

I would agree. I finally just threw the instructions away and figured it out myself.

So far I am happy with my install. The rear took 15 minutes to do and the front took 1/2 hour each. I found the instructions adequate for my 13 F150.

Be sure to check the fishing tool provided with the supplied bolts. With my Torklift tie-down kit the fishing tool was undersized for the size bolts provided and this made it extremely difficult to remove them without damaging the spring like end.

I was glad that I did the work myself as it took an extra 6 hours as the parts did not fit properly at the front or the rear. At the front mounts I trimmed off part of the tiedown so the bolts for the bed of the truck could go all the way into the factory holes.

At the rear the bracket as provided by Torklift was pressing against a fuel line and a brake line. I used a power hacksaw to trim the brackets and then ground them smooth and painted the brackets after verifying that they would fit properly.

Overall what should have taken an hour or two was an all day project. As I stated I was glad I was not paying an hourly shop rate to have the work done and I am 100% sure that a mechanic would have force fit the front bracket and half the threads of the bolt would not be making contact with the frame and the rear bracket would have been rubbing against the brake and fuel lines until I had a failure.

I have been installing aftermarket products like this on my trucks for over 30 years and actually I am surprised when an installation goes smoothly with a good fit without having to modify anything. In contrast to the Torklift tiedowns which took a day to get installed properly, I installed the Supersprings on my truck in less than an hour and it took about 30 minutes to install a Big Wig anti-sway bar.

Crumm wrote:

I felt that for my model the instruction manual was very difficult to follow, pictures were not in order as far as I could tell, and they were hard to see. I wish they could have color pictures.

I would agree. I finally just threw the instructions away and figured it out myself.

I would agree the directions were poor at best... Just looked at it and figured it out on my own..