Electrical or Air Cond. Problem?

Golden_HVAC wrote:
It does sound like a bad connection.

Yup, I agree with that, sounds like a bad connection to me. The hot dogbone is a clue the plug that plugs into it, or the outlet it is plugged into, may be in need of either cleaning or attention. (They often do, I just did my plug I think the weekend before last).

It could also be too many feet of too small wire between the RV and the Transformer back on the pole not far from your house.

Where I'm at now they used Aluminum wire for the feeds to the park outlets.... I see what you talk about all the time.

Chuck,
I did check the voltage at the house 120.9...when I was having the problem the fridge was on electric. I switched to gas and nothing changed. I ran the a/c 4 hours today and voltage was 109 to 113 as it should be. I think "imgoin4it" may have the best idea, basically too much draw from the panel.
I am glad all seemed to work as it should today. I do plan on removing the cover on A/C tomorrow and give everything up there a good cleaning.
Thanks!

Perhaps the battery charger in the converter started? Or maybe the fridge was on electric?

Next time, see if you can check the voltage at the outlet in the house while RV connected. Is RV on its own circuit?

There is a start cicator but there is also a run capicator....if the start capicator is bad the outdoor fan and the blower will come on and u will hear the compressor try to come on....if the run capicator is bad usually u will hear just a loud humming sound....the blower will run but the outdoor fan might run and it ,ought not....

No sir, the water heater is not on...one of the first things I checked.
Thanks!

For the last month as a hobby I have been helping Eduardo at his large merchandise store. He purchases returns, tests them "Returned because color is wrong, size, shape, does not work (special battery was stolen out of the package)".

Includes extension cords, plugs and adapters.

A frightening percentage of the Chinese stuff is sent out of the factory "Ready To Catch Fire". Too thin a gauge clips and prongs, incorrectly crimped terminals, etc. I use the Harbor Freight sockets and plugs and manually rewire bad stuff and then amp test it to full capacity.

My advise when using a "new" replacement power device is to not assssssume it is good, especially if "one just like it" had just about caught fire. The cultural freedom brigade of the flying hummingbird honorable factory number 88 might have had a bad day.

"Comrad, Xin tells me the crimping machine has not been working good"

"For how long comrad Li?"

"He does not know"

"Agh! Do we tell the colonel about this most unfortunate accident"

"Don't be a fool Li! You know what the colonel threatened the last time an unfortunate accident occurred"

"Put them on the bottom of the pallet, and ship them out, fast!"

At 100v are you sure the electric water heater was not on?
Otherwise I would be mapping out where the system loses voltage at each step from home breaker panel to the RV breaker panel.

Thanks for the comments, I think I see possibilities from each of you. Today I went out and turned the a/c on and all was well...I had 113 volts. I did find this morning the a/c was on low fan rather than high. I have learned from this forum that can cause the a/c to freeze up, however I cannot believe mine froze up as our temp yesterday was well into the ninety's. I let the unit run today for 3 hours and recorded the time and what the volts were each time. Never had a reading lower than 109 and most of the time it was 113. Only other item on was the refrigerator.I am wired into the house panel and am roughly 70 feet from the 5er. Don't recall the gauge wire we used but did take that into consideration at the time of installation. Have always been careful not to have too much electrical going at one time and have not had a problem until yesterday. I am starting to believe the suggestion of my being so far away from the house, I may be overtaxing the system.
Thanks to all....will advise if the unit repeats yesterday.
Weldon

A atart capacitor is that--It STARTS the compressor and is only needed to do that. Once the Compressor is running, it is not needed. Your problem may be a bad compressor or more likely a voltage supply problem. Doug

I would expect the "problem" is with the overall electrical load at your residence. I am guessing your 30 amp outlet is farther away from your panel then most outlets in the house, and while you are running an acnd in the RV if the residential acnd starts, could be electric hot water heater, oven or any other sizeable load comes on you may be "over taxing", amps go up volts go down, the electrical system in your house. Mine does exactly as you describe on hoy days so I have to make it a point not to run the RV air. I also have a long extension cord from the 30amp connection to the RV.