No Electric When Hooked up

Thanks for the update!

I got it completed late evening,i put the 2 extra wires on Aux neutrals and i tested just plugged to regular plug in with dog bone and i had electric to the microwave but i didnt fire the heat pump on it due to small plug in, and next i fired the generator and microwave worked and i also fired the Heat Pump and it worked as well so i think i may be clear for Take off as you can see the Parallax Box is a much neater setup than old box... so thanks so much to all you who chimed in



Click For Full-Size Image.

The top white on went to same neutral at bottom only on other side of switch in old box

The lower one appears to be connected to neutral on bottom feed. It should be connected in same location.
The upper one needs to get connected to same neutral function as the wire nut. Can you tell what this circuit feeds?
Many terminals are not designed for connection of multiple conducts. Be careful when terminating on new box. Make sure each conductor is tight.
It sure looks like some one added items whether it was during construction or afterward.

ss340duster wrote:
This is inside my box notice the extra white wires on shore line and going in to the coach

On My gen side i have 2 black, 2 white and 1 green
so does big black go to gen L1, blk yellow to gen L2, 1 white to gen Neutral, 1 white to gen AUX, or do double white on Gen Neutral,?

On My Shore line which is middle on mine i have 2 blacks 2 whites and 1 green, so does big black wire go on L1,lil black go L2, & 1 white to Line neutral and 1 white to Line Aux or do i double the white on Line Neutral!

On My load side going to Coach i have
2 black and 2 white and 2 bare copper
Grounds
so do i do 1 black to load 1, 1 black to load 2, 1 white to load neutral and one white to load Aux or double on load neutral ?

i just dont want to swap this and fry a 260 dollar switch and as you can see im not sure of myself but this thing got to get swapped tommorrow LOL

My only concern is the the 2 white wires that are going to the wire nuts on my old box if I should attach those to aux on new box

No time for that

Hire an electrician

Yours is enough different I wouldn't have a clue how to advise you.

You probably need to call Winnebago or Parallax. I called Parallax with a question concerning the jumper cables when I did my install. They seemed knowledgeable and were helpful.

cpd520 wrote:
Mine is a 50 amp service on a 2004 Itasca. Just put in the ats 501 switch.



Mine is as shown below:
Generator
Gen L1 - black
Gen L2 - Black w/yellow stripe
Gen neutral - White marked neutral
Aux Gen - White

Shore line
Line 2 - Red
Line 1 - Black
Line Neutral - White

Going to coach
Load 2 - Red
Load 1 - Black
Load neutral - White
Load aux

Good luck with your install.

On Mine With my old PS245L

On My gen side i have 2 black, 2 white and 1 green
so does big black go to gen L1, blk yellow to gen L2, 1 white to gen Neutral, 1 white to gen AUX, or do double white on Gen Neutral,?

On My Shore line which is middle on mine i have 2 blacks 2 whites and 1 green, so does big black wire go on L1,lil black go L2, & 1 white to Line neutral and 1 white to Line Aux or do i double the white on Line Neutral!

On My load side going to Coach i have
2 black and 2 white and 2 bare copper Grounds
so do i do 1 black to load 1, 1 black to load 2, 1 white to load neutral and one white to load Aux or double on load neutral ?

i just dont want to swap this and fry a 260 dollar switch and as you can see im not sure of myself but this thing got to get swapped tommorrow LOL