split 50 amp into 2 - 30 amp

Water-Bug wrote:

Bird Freak wrote:

john&bet wrote:
The safety of the idea has not been address yet so let me be the first. You have the potential to overload the neutral of the adapter or the neutral of the recptical or the neutral anywhere up stream of that point. If both 30 amps are loaded to say 24 amps then there is 48 amps on the neutral which will be pushing it and the connections. JMHO.

I may be wrong but I don't think this is right. I believe a 50 amp plug has 2 neutral's and 2 hot's and a ground both hots are 50 amp. If so than you will only pull 30 amps from each 50 amp lead if your plug just splits to 2 30 amp plugs.

X2

An RV 30 amp circuit has a single 30 amp leg or app 3000+ watts capacity. An RV 50 amp circuit has 2 ea 50 amp leg of app 5000+ watts each for a total of 10, 000+ watts.

EDIT The 50 amp RV circuit has 2 hot, 1 neutral and 1 ground pins.

I stand corrected. Must have had a brain fart.

The neutral thing is not an issue. This is exactly how your breaker panel in your house is wired. Each leg does not have it own Neutral, they share one.

john&bet wrote:
The safety of the idea has not been address yet so let me be the first. You have the potential to overload the neutral of the adapter or the neutral of the recptical or the neutral anywhere up stream of that point. If both 30 amps are loaded to say 24 amps then there is 48 amps on the neutral which will be pushing it and the connections. JMHO.

And what is the difference
Between that and a 50 amp rig using the same amount (24) on each of it's legs

That 50amp is 50 amps on each leg , 100 amps total
Two 30 amp rigs can only use 30 amps on each leg

50 amp RV is wired as two 120v 50 amp legs neutral load is not zero, not 240v
There's always a neutral current equal

john&bet wrote:
The safety of the idea has not been address yet so let me be the first. You have the potential to overload the neutral of the adapter or the neutral of the recptical or the neutral anywhere up stream of that point. If both 30 amps are loaded to say 24 amps then there is 48 amps on the neutral which will be pushing it and the connections. JMHO.

With 24 amps on each leg you will have 0 on the neutral. Overloading it is not a concern. The most you could possibly put on the neutral would be 30 amps. This would occur with a 30 amp load on one leg and nothing on the other.



And no, a 50 A circuit does not have 2 neutrals.

john&bet wrote:
The safety of the idea has not been address yet so let me be the first. You have the potential to overload the neutral of the adapter or the neutral of the recptical or the neutral anywhere up stream of that point. If both 30 amps are loaded to say 24 amps then there is 48 amps on the neutral which will be pushing it and the connections. JMHO.

I might be wrong, but I think the neutral will only see the delta amps between the two 50A legs and in your example that should be 0. The only safety issue is if a short happens between the 30A on the dogbone and the 30A CB in the trailer that 30A rated line could be subject to 50A, but is no different than using a single 50A to 30A dogbone which is common practice.

I see no additional safety concerns in what is being recommended except for the fact that those 30A connections are not weatherproof or protected in the linked configurations whereas mine with the in use weatherproof covers solves that safety concern.

Here are pics of my 50A to dual 30A dogbone






Larry

Bird Freak wrote:

john&bet wrote:
The safety of the idea has not been address yet so let me be the first. You have the potential to overload the neutral of the adapter or the neutral of the recptical or the neutral anywhere up stream of that point. If both 30 amps are loaded to say 24 amps then there is 48 amps on the neutral which will be pushing it and the connections. JMHO.

I may be wrong but I don't think this is right. I believe a 50 amp plug has 2 neutral's and 2 hot's and a ground both hots are 50 amp. If so than you will only pull 30 amps from each 50 amp lead if your plug just splits to 2 30 amp plugs.

X2

An RV 30 amp circuit has a single 30 amp leg or app 3000+ watts capacity. An RV 50 amp circuit has 2 ea 50 amp leg of app 5000+ watts each for a total of 10, 000+ watts.

EDIT The 50 amp RV circuit has 2 hot, 1 neutral and 1 ground pins.

john&bet wrote:
The safety of the idea has not been address yet so let me be the first. You have the potential to overload the neutral of the adapter or the neutral of the recptical or the neutral anywhere up stream of that point. If both 30 amps are loaded to say 24 amps then there is 48 amps on the neutral which will be pushing it and the connections. JMHO.

I may be wrong but I don't think this is right. I believe a 50 amp plug has 2 neutral's and 2 hot's and a ground both hots are 50 amp. If so than you will only pull 30 amps from each 50 amp lead if your plug just splits to 2 30 amp plugs.

Got mine on amazon 2 30 amp male to 50 amp female also has led lights to show power and got it less than $70. Worked great.

The safety of the idea has not been address yet so let me be the first. You have the potential to overload the neutral of the adapter or the neutral of the recptical or the neutral anywhere up stream of that point. If both 30 amps are loaded to say 24 amps then there is 48 amps on the neutral which will be pushing it and the connections. JMHO.

Hi,

Or you can create a breakout box that has 30 amp breakers for each leg.