Onan Microquiet 4000 "No Crank"
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep-15-2014 06:20 PM
Again this is a no crank condition, not a cranks and wont start.
I jumped across the solenoid and it cranks but wont start unless I hold the start button or the stop button down. Then it will start and run as long as you hold the button down. Of course if you hold it down in the start position too long it will shut off and give you the over crank code. It will run as long as I want holding the stop button down but does not produce 120v while holding the button down.
Any ideas?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep-16-2014 06:06 PM
GPSTECH wrote:
Ahhh Perfect
Thanks Kpack
I have bouted with several of those spec k generators they have no battery charger they are pretty finicky about the battery gr. Slip rings and brushes can be a problem they have to be making electricity to run. Ps be carful with that starter when you jump across the solenoid to energize the starter and it's running that's the starter turning it to run. So I wouldn't do that to long.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep-16-2014 05:56 PM
'01 31' Rexall Vision, Generac 5.5k, 1000 watt Honda, PD 9245 conv, 300 watts Solar, 150 watt inv, 2 Cos 6v batts, ammeters, led voltmeters all over the place, KD/sat, 2 Oly Cat heaters w/ ox, and towing a 2012 Liberty, Lowe bass boat, or a Kawi Mule.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep-16-2014 05:35 PM
2003 Jayco Escapade 31A on 2002 Ford E450 V10 4R100 218" WB
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep-16-2014 05:26 PM
Thanks Kpack
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep-16-2014 04:56 PM
https://www.dropbox.com/s/5odhzt9r60x91cj/981-0530Ckyser.pdf?dl=0
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep-16-2014 03:09 PM
Spek k
No idea on the hours
The solenoid is good. When I apply 12v to the small terminal that is supposed to operate the solenoid it engages and the starter goes to working. Then if I push the start or stop button the fuel pump runs and it starts. However, when I release the button it dies I assume this is because the fuel pump stops.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep-16-2014 02:49 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep-16-2014 02:01 PM
I'm thinking some kind of control module or circuit board?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep-16-2014 01:37 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep-16-2014 01:07 PM