Can Dicor be used as an adhesive??

ryanw821 wrote:

LarryJM wrote:
I haven't read all the posts, but I would not recommend using Eternabond even the double sided stuff to secure anything. It is not a good adhesive since the microsealant is soft especially when warm and stretches. If you pull on the microsealant constantly it will release a lot of times from the surface. If you want a good adhesive look at either the 3M Marine UV 4000 and if securing items like wires the 5200 might be O.K. however the 5200 is not UV protected so I'm not sure how long it would last.

Larry

I ended up using 3M 5200, but it's on the back side, so should not get any sunlight/UV.

That is by far the best to use between two surfaces, but remember you will NEVER BE ABLE TO REMOVE the item without destroying either the item or the surface. I have what I would call extensive individual usage experience with both the regular roof seal and the double sided Eternabond in probably as many applications as anyone here.

Larry

LarryJM wrote:
I haven't read all the posts, but I would not recommend using Eternabond even the double sided stuff to secure anything. It is not a good adhesive since the microsealant is soft especially when warm and stretches. If you pull on the microsealant constantly it will release a lot of times from the surface. If you want a good adhesive look at either the 3M Marine UV 4000 and if securing items like wires the 5200 might be O.K. however the 5200 is not UV protected so I'm not sure how long it would last.

Larry

I ended up using 3M 5200, but it's on the back side, so should not get any sunlight/UV.

I haven't read all the posts, but I would not recommend using Eternabond even the double sided stuff to secure anything. It is not a good adhesive since the microsealant is soft especially when warm and stretches. If you pull on the microsealant constantly it will release a lot of times from the surface. If you want a good adhesive look at either the 3M Marine UV 4000 and if securing items like wires the 5200 might be O.K. however the 5200 is not UV protected so I'm not sure how long it would last.

Larry

My Roadtrek wrote:
3M VHB auto moulding tape. Strong, easy to use, and can be removed.

I wanted this install to be permanent, but that's a good thought, I've used the 3M VHB tape before installing my LED "panel" lights and for some automotive uses, not totally sure I would trust it for a solar panel though, maybe.

Here's the panel install with wiring completed:

MPPT Controller:

Wiring to factory battery cables:

3M VHB auto moulding tape. Strong, easy to use, and can be removed.

Going to update you all on my progress, I have been busy yesterday and today working on this, I took the advice of WESTEND and used a tube of 3M 5200 Marine adhesive (let it sit overnight), and followed that up with 4" Eternabond tape around the edges, so there's no way wind can exert any upward force on the panel. It doesn't really show it in the pic (through a dirty 2nd floor window), but I scrubbed that half of the roof with a soft bristle brush and roof cleaner before any work began.

It is still a work in progress, I still have more to do (running cabling, sealing cable entrance, etc...), but I think this is going to work out just fine.

Dicor is not a good adhesive. Don't ask how I know this.

Dicor would not be a very good, or long lasting adhesive IMO.

I should also note, I plan on eternabonding the wires down to keep them from catching wind and brushing/chafing against the roof and potentially causing nicks/tears in the roof. I see so many installs where people have screwed in wire clips/guides and then hit the screws with dicor, I am of the train of thought that the fewer holes in my roof to start with the better, so I figure taping down the wires will be best.
The ONLY hole I plan in my roof is the one where the wires go in, which I will dicor the heck out of and then probably eternabond around that, I am paranoid of and DON'T want leaks, lol

Huntindog wrote:
Have you ever tried to remove Dicor? It's VERY difficult to do.
So I had no problem using it as an adhesive for a stainless steel plate I glued to the roof where the wheel to my Wingard Traveler hits it. It works really well. Probably cheaper than what a roll of double sided Eternabond will cost too.

That was my thought, and why I asked, but it sounds like double sided eternabond or 3M marine adhesive are both good candidates too, decisions, decisions, I am going to have to weigh all this advice and decide on what to do, lol


I will post photos of my project once I am completed, hopefully I have enough time before our next camping trip in a few weeks, will be nice to not have to worry about battery levels quite so much.