So what did you do to your Truck Camper today?

mountainkowboy wrote:
Nothing in 60+mph winds.

Our winds finally took a break, and I was able to take the camper off the truck, and got the pallets and blocks under it for stability before the winds kick up again! And when we have a day that it isn't raining or snowing, I can crawl under and install my new gray water tank and get it plumbed in. Then I can add the floor insulation. Hate to take it off, but more snow is coming, and really don't like plowing with the camper on because I can't see to the rear real good. But i will miss the weight in the bed of the truck!;)

Keep up the ideas for the camper projects!!!

Garry

As much as didn't want to I drained the water from the rig. In the next few days I'll put anti-freeze it.

Buzzcut1 wrote:

mountainkowboy wrote:
Nothing in 60+mph winds.

Got that right. Just glad the oak tree that blew
over missed my tc

We havent lost any trees yet, but theres alot of branches on the ground.

mountainkowboy wrote:
Nothing in 60+mph winds.

Got that right. Just glad the oak tree that blew
over missed my tc

Nothing in 60+mph winds.

A little late from last week, But we CAMPED in the camper! In weather that ranged from a low-low of 11F below zero to a high-high of 16F above zero!

Garry in AK

mark_ be , that was one long day ! LOL

Here's what I've done until now: (all at once)

* installing 3 transformers, because we have 230V and the original camper stuff works on 120V. It works great and can use everything (sockets and appliances) at any time - on ac and on generator and I even have the choise of using 120V or 230V as shore voltage - only problem is that the microwave generates less heat on 50Hz than 60, but might be fixed - would have to contact manufacturer for that)
* placing adapters onto the original LP ACME connector, so LP bottles with DIN connector can be used.
* placing 2 28 liter European LP bottles that can be filled at the pump. (automatically stops filling @ 80% = 22 liter = 5.8 gallon) Most European bottles are trade-in bottles and different by country and is not very handy for an RV, if you ask me. European refillable bottles can be filled like US horizontal tanks, so don't have to be removed. (so paid per liter/gal, not per gram/ounce)
* 22 inch LED-TV
* Voltage stabilizer for TV (perfect 12V output with a variable input from 5 to 20 volts or so)
* cable gutter from left to right against the roof at the foot side of the bed to accommodate the cables for TV (12V - coax - av-cable)
* cheap rear view camera - needs to be replaced, because of bad result (what have I saved now...)
* digital thermometer/atomic clock inside + outside sensor + basement sensor
* 2000W pure sine-wave inverter
* 2nd battery
* Surepower battery isolator (camper shop apparently didn't install that)
* Replacing the 120V heating element in the fridge (connected it to 230V by mistake - wanted to go too fast when installing transformers)
* re-installing the 3-way winterizing valve that was connected the wrong way by the manufacturer
* fixed bad electrical connection at right rear running light
* re-caulked the shower wall - had a 1/8 inch gap
* installing a foolproof 120V connection for the engine block heater, placed behind the appliance access door - foolproof because we get 230V inside
* fixing a whole list of things for the truck (by dealer, not by me)
* husky liners in the truck (front, center hump and back)
* navigon carkit for iPhone (called Mio carkit in Europe) - together with a 3.5mm jack to cassette adaptor
* laminated weight and dimensions reminder chart in meters and feet / kilograms and pounds (for bridges and tunnels) and on the back side: translations for potable water and diesel in many languages (who knows where we're going to end)

No sockets were replaced (but do provide 230V now - only sockets under dinette are still 120V), because I wanted to keep the camper as original as possible. We use adapters instead.

kerry4951 wrote:
Started to run the wiring for a 2nd (roof mounted) camera. Decided I want to be able to see out front and overhead to keep an eye on "low clearance" issues and tree branches.

Wow, Kerry. Another mod? You are a busy little bee. :)

kerry4951 wrote:
Started to run the wiring for a 2nd (roof mounted) camera. Decided I want to be able to see out front and overhead to keep an eye on "low clearance" issues and tree branches.

Great idea...