2008 winnebago access slide not working??

jwlong wrote:
Ok everyone let me update you.... Tonight I went out and manually cranked slide out. I was able to get the touch pad to go into manual mode and the slides came in. That immediately told me I have power to the slide. However the slide would not go out still flashed parking brake light. So I manually cranked slide out again. Running out of ideas I decided to push parking brake all the way down to the floor. What do you know the slide came in like it should, and now goes out like it should. I had ruled the parking brake out do to the rear slide working. How ever the parking brake sends two separate signals to two separate controllers. I could make it not work by not pushing brake all the way down. I never would have guessed that the brake would need pushed all the way down but it worked. Thanks to everyone who offered suggestions and happy camping!

Glad to hear it! Happy travels!

Ok everyone let me update you.... Tonight I went out and manually cranked slide out. I was able to get the touch pad to go into manual mode and the slides came in. That immediately told me I have power to the slide. However the slide would not go out still flashed parking brake light. So I manually cranked slide out again. Running out of ideas I decided to push parking brake all the way down to the floor. What do you know the slide came in like it should, and now goes out like it should. I had ruled the parking brake out do to the rear slide working. How ever the parking brake sends two separate signals to two separate controllers. I could make it not work by not pushing brake all the way down. I never would have guessed that the brake would need pushed all the way down but it worked. Thanks to everyone who offered suggestions and happy camping!

We had a problem with our slide - here's a copy/paste/modify of a post I made last year on it...

We had a problem with ours coming in on its own with the parking brake set, so it was moving but obviously something was wrong. DH talked with both Winnebago then Kwikee. We started with replacing the switch (the cheapest fix), which didn't do the trick. Then on to the control module. Since our year didn't have a key shutoff we added a switched 40 amp cutoff switch. The combination of these two has done the trick for us...the power switch alone keeps us from ever seeing it happen again, so it is hard to say with certainty that the control module replacement fixed it.

The problem seems to be that the slide control (at least on ours) is in one of the storage hatches, which are those nice blow mold water-tight areas. But a bit of moisture in there will stay in there and we tend to think that the humidity in there played into our problem.

I wonder if you're seeing a problem because of moisture as well?

Best of luck!

jwlong wrote:
Yes emergency brake is set. Back slide works fine. Front slide switch panel flashes the parking brake light but I know it is set properly since the back slide works

If the back slide works, that points to the slide. I wonder if there is a fuse somewhere for the slides.

I'd suggest resetting the emergency brake. I have heard of problems with the brake not being set "just right".

.

Yes emergency brake is set. Back slide works fine. Front slide switch panel flashes the parking brake light but I know it is set properly since the back slide works

Is the emergency brake on? Mine won't slide without it on.

Thanks for the reply. I have ruled out the switch panel itself. My slides are on to separate switch panels and I swapped them and it was no change. I have chased wires and checked grounds all seems to be good. Any ideas where the control module may be located. I have heard those to give problems as well. Im not sure how to reset the system?? Thanks again. Ill take any help I can get!

I have a 2008 31C Outlook that I have had slide problems with. I have been told the slide motor shuts off when they sense a surge when closing or opening since there is no real on/off switch and therefore are very sensitive. It is stated on the owners manual and emphasized to me by mechanics as well to keep the motorhome engine running while moving the slide in or out. With regards to your particular problem you might consider resetting your slide motors which can be easily done. This allows the front and back slide motors to operate independently so you can be sure they are both closed all the way and in sync.