Leak near Valve/Tank Connection

And a guy has a leak and half the people start discussing the virtues and drawbacks of tank level monitors….

Even IF the vent is plugged or dropped into the liquid as soon as you flush the tank is vented and liquid will flow in (and gasses out) until the tank is full. This is given that the toilet empties into the top of the tank, hard to imagine otherwise.

Use This to post pictures

Even if his vent pipe is too far down inside his black tank it shouldn't leak. Fix the leak.

It could just be the weight of the water causing it to leak at a poorly sealed joint. Fix the leak

His piping leaks, the level of chit in the tank is immaterial (as is the size of the vent). There is no “pressure vent”. There is only a vent. If his tank was “pressurized”, he would certainly be well aware of that fact every time he flushed the toilet - he would get a rude face wash.

Gdetrailer wrote:

Dusty R wrote:
The SeeLeval is a system that circuit boards that attach/glue to the side of the tanks and measure the level/densaty of the tank, in 10's .

:R

Yes Dusty, I suspect most folks are aware of "SeeLevel" and its "advantages"..

But it is not cheap, depending on tank placement may be a real pain in the rear to install or even not be able to install, it replaces an existing system which is already in place so now you have a old and new monitor.. Not to mention you are adding more complex circuit boards and electronics which can and do fail.

Mine is built into the rangehood and simple as dirt so I would have to poke a new hole in the paneling..

It's cheaper and easier to just ensure your the probes are not holding on to waste material don't you think?

Good proper dumping procedure seems to work pretty well and only costs a couple of squirts of dish detergent and copious amounts of water each dump.. Mine is going on 40 yrs old and still working but I guess mine is the only ones in this world that works correctly so I must be doing something wrong?..

That would depend on your definition of cheap. A seelevel 3 tank system is @ $220. A drive motor for a Dometic 9100 awning is over $700.00 and if you ever need to but anything from Lippert they'll soak you good.

I've installed 3 seelevel systems on 3 different rigs and all were less than a 3 hour install including opening or dropping underliner. On two I was able to use the existing wiring to the idiotic problematic ORM sensor system which was a PITA on all 3 rigs.

Dusty R wrote:
The SeeLeval is a system that circuit boards that attach/glue to the side of the tanks and measure the level/densaty of the tank, in 10's .

:R

Yes Dusty, I suspect most folks are aware of "SeeLevel" and its "advantages"..

But it is not cheap, depending on tank placement may be a real pain in the rear to install or even not be able to install, it replaces an existing system which is already in place so now you have a old and new monitor.. Not to mention you are adding more complex circuit boards and electronics which can and do fail.

Mine is built into the rangehood and simple as dirt so I would have to poke a new hole in the paneling..

It's cheaper and easier to just ensure your the probes are not holding on to waste material don't you think?

Good proper dumping procedure seems to work pretty well and only costs a couple of squirts of dish detergent and copious amounts of water each dump.. Mine is going on 40 yrs old and still working but I guess mine is the only ones in this world that works correctly so I must be doing something wrong?..

The SeeLeval is a system that circuit boards that attach/glue to the side of the tanks and measure the level/densaty of the tank, in 10's .

CA Traveler wrote:
I was thinking 1.5" but regardless of the cause the leak should be fixed.

Also wondering how he knows it's 3/4 full. Typically grey/black gauges are very inaccurate.

I would call them unreliable more so than inaccurate..

The unreliable comes from the sensors often getting fouled up with waste not getting cleaned off of them..

Clean probes will be pretty spot on accurate since they are physically installed and don't move around..

Get em clean each time you dump and they work well, mine are in a 1984 TT, bought it used and yet my sensors work very well.

I dump the waste, then add some Dawn dish detergent and fill the tanks to 3/4 and then dump that.. Has worked well for me.

Take a look at SeeLeval gauges for RV holding tanks. The read in much more accurate. If I remember right 10's of the tanks. Not very hard to install.

I was thinking 1.5" but regardless of the cause the leak should be fixed.

Also wondering how he knows it's 3/4 full. Typically grey/black gauges are very inaccurate.