Wheel chocks for single axle?

[penguin149]

What do you guys use as wheel chocks for a single axle trailer? I've been using a store bought plastic chock in front and back on both sides of the trailer. These seems to move around some and get loose over time. On my previous dual axle trailers, I had a homemade chock made from 2 4x4 wedges that I put in between the tires and tightened a wing nut on a threaded rod.

Thanks!

[ajohn14]

penguin149 wrote:
What do you guys use as wheel chocks for a single axle trailer? I've been using a store bought plastic chock in front and back on both sides of the trailer. These seems to move around some and get loose over time. On my previous dual axle trailers, I had a homemade chock made from 2 4x4 wedges that I put in between the tires and tightened a wing nut on a threaded rod.

Thanks!

I had the same issue with my coyote, what I found is a DIY solution that works really well. It is a home made wheel chocks that we use on our airplane. They are simply made out of 2x4s, Screw and glue 3 15"-18" pieces of 2x4 together in a U shape with open end of the U slightly wider than the closed end (measure it around your trailers tire) place on the ground so that the open end is hugging the tire and tap into place with a rubber mallet, so that the tire is wedged into the chock. They hold tight and really take nearly all of the movement out of the trailer. I painted mine so I could see them and help them last longer, they work great and were nearly free as I had all the material on hand already

[Dog_Folks]

Padlin wrote:

Lynnmor wrote:

poppin_fresh wrote:

robsouth wrote:
poppin_fresh wins the "cupie doll"!!!

I have to admit that I have no idea what that means.

Is winning a "cupie doll" good or bad? 🙂

You wouldn't understand if you ain't an old geezer.

For a single axle, I wouldn't use the slippery plastic chocks.

Didn't realize I had graduated to Old Geezer, can I get my status at the left changed?

No you cannot. The Old Geezer is a secret club.:B

[Padlin]

Lynnmor wrote:

poppin_fresh wrote:

robsouth wrote:
poppin_fresh wins the "cupie doll"!!!

I have to admit that I have no idea what that means.

Is winning a "cupie doll" good or bad? 🙂

You wouldn't understand if you ain't an old geezer.

For a single axle, I wouldn't use the slippery plastic chocks.

Didn't realize I had graduated to Old Geezer, can I get my status at the left changed?

[Dog_Folks]

poppin_fresh wrote:
It sounds like you aren't chocking properly if they are coming loose. What you want to do is "catch" the tire.

You do this by placing a chock either in front of, or behind the tire. Then, use the tow vehicle to push or pull the trailer (depending on where you placed the chock) slightly up the chock to apply pressure.

While the pressure is applied, place another chock on the other side of the tire, nice and tight to it.

Now, let the pressure off of your vehicle and the tire will roll down only slightly before being caught by the second chock.

When done properly there is pressure being applied to both chocks to the point you can't remove either one without reversing the process. Because of this you should find your trailer nice and stable.

It's easiest to do this method with two people, but you can do it solo by using the emergency brake.

Jon

This is the way to do it. We do it with one axle on our tandem set up and it has worked great for years.

[Lynnmor]

poppin_fresh wrote:

robsouth wrote:
poppin_fresh wins the "cupie doll"!!!

I have to admit that I have no idea what that means.

Is winning a "cupie doll" good or bad? 🙂

You wouldn't understand if you ain't an old geezer.

For a single axle, I wouldn't use the slippery plastic chocks.

[old_guy]

I've seen people hit the chocks with a hammer to drive them into the locking position. didn't stay around long enough to see if they stayed in the locked position.

[DonNH]

I like the heavy rubber chocks I got from Harbor Freight for about $8 each.

Best is to load them up as Popnfresh described, but pushing them in as tight as possible and then checking periodically works too.

I've been meaning to try setting up a pair with bungee cords to pull them together to keep them tight against the wheel.

Like the idea of the Bal leveler but am too cheap. That still leaves the low side wheel needing chocks.

Don

[poppin_fresh]

robsouth wrote:
poppin_fresh wins the "cupie doll"!!!

I have to admit that I have no idea what that means.

Is winning a "cupie doll" good or bad? 🙂

[robsouth]

poppin_fresh wins the "cupie doll"!!!

[poppin_fresh]

It sounds like you aren't chocking properly if they are coming loose. What you want to do is "catch" the tire.

You do this by placing a chock either in front of, or behind the tire. Then, use the tow vehicle to push or pull the trailer (depending on where you placed the chock) slightly up the chock to apply pressure.

While the pressure is applied, place another chock on the other side of the tire, nice and tight to it.

Now, let the pressure off of your vehicle and the tire will roll down only slightly before being caught by the second chock.

When done properly there is pressure being applied to both chocks to the point you can't remove either one without reversing the process. Because of this you should find your trailer nice and stable.

It's easiest to do this method with two people, but you can do it solo by using the emergency brake.

Jon

[mbutts]

I vote for the Bal Leveler, very handy device!

[gheicher]

Bought a Bal tire leveler / wheel chock for my AR-One. Does both leveling and chocking with one device. Not as cheap as a couple blocks of wood, but very convenient,easy to use, and neat to stow.

Bal Tire Leveler

[harold1946]

Purchase some 24 penny spikes and drive the in to hold the chocks in place.