New trailer next week, which Andersen WDH?

Sounds reasonable to me.

Alright, I'm sold. I'm getting the model with the 2.5 inch shank, the 4 inch drop, and the 2 5/16 ball. This is for a non-lifted truck and a standard TT. I'll attach the ball and hitch at the lot, but install the actually WDH part at home. I should be able to get the trailer 20 miles home on the freeway just by keeping it slow. We don't have much wind around here. Does this sound like a reasonable plan?

rvshrinker wrote:

ScottG wrote:
We're talking about two different things. The OP brought up WDH which is seperate from sway control.

Believe the Andersen WDHs have sway control built in.

You are correct. It is both. The sway control is wonderful. Also with the Andersen you get none of that jerk, jerk, jerk when on concrete roads when you go over the separations in the road.

ScottG wrote:
We're talking about two different things. The OP brought up WDH which is seperate from sway control.

Believe the Andersen WDHs have sway control built in.

We're talking about two different things. The OP brought up WDH which is seperate from sway control.

The only thing your going to have to measure is for the distance of the ball height to the trucks hitch receiver. The standard is a 6" rise or drop bar, and if more is needed a 8" bar can be ordered. If you'll go over the instructions you'll figure it out. I have an Andersen WDH myself, works great. Had a couple who can to the park I camp hosted at this summer with a lot bigger trailer then yours.

I recently replaced my Husky WDH from previous owner with an Andersen hitch and I am extremely satisfied with the change. It is clean and light to handle. It is also quick to hook up. And it is silent, no popping, squealing, etc. like from the old hitch. I ordered the 3347 for 4 5/8" frame with 8" drop for my setup, a Grand Cherokee and an Earthbound 29' with an approximate tongue weight of 500-600 lbs depending upon loading. That is another advantage of the Andersen, you can fine tune the chain tension based upon your load distribution and hitch weight. It can also be used as you upgrade TT or TW because of it's wide range of supported weights. There is no way I would go back.

I bought a new-to-me ORV TT this summer. It's similar to yours in weight & length and comes with a WD hitch without anti-sway. The previous owner tows with a Ram 3500 and claims he doesn't need anti-sway bar.
I tow with a Chevy 1500HD and have spent close to this entire summer looking for a WD Hitch with anti-sway features. I had 20 yrs experiences on a Reese Dual Cam and quite happy with it. However, the new DC requires drilling on the TT frame for installation and that's something I try to avoid. I had a close look at the Andersen hitches. Its light-weight and non-greasy features drawn me to it. The pros and cons are just like the other post said. The model number 3350 the Andersen rep quoted you would be the one for my TT as well rating wise. In the end, with consideration on my 970# tongue weight, I got cold feet and settled on a Equal-i-zer 12,000# WD Hitch. What sold me was the complete bolt-on installation and it doesn't rely on the clamps to counter-act the weight transfer. I haven't had a chance to test it out since I had it installed last weekend so there's not much I can report on its performance. I will take a short camping trip tomorrow and see how it goes.
Like other post suggested, if the receiver on your truck can handle your TT's tongue wt, you can hook it up and tow it home. In my case, my receiver is only good for 500# TW without WD Hitch. But I know some newer 3/4T P-U do have higher rated receiver.
Now that I have installed my hitch, I realize I could be a good candidate for an Anderson hitch, and so could you too. During my set-up of the WD Hitch, I noticed the front axle only lifted 1/4" without the spring bars mounted. I think this is due to my 3000# rated rear axle and long wheel base of the crew cab. So in your case, with a 3500 P-U, the weight transfer factor is not that critical. An Andersen could work well for you.

With a RAM 3500 and only going 20 miles I would hook it up without the WDH. Way back in the early 60s we never had WDH , just set it on the ball and go. I towed like that for years before I bought my first E Z Lift Hitch and that was 1/2 ton P/Ups, After arriving home then you can take your time and set the Anderson up right

This will revive an old argument but I would like to hear from anybody that has actually had trouble in this weight range with the Andersen. All I ever read is from people who have guessed that would be a problem. I have a trailer that is rated almost 10,000# fully loaded and have absolutely no problems transferring weight.The system you are looking at is rated to 14,000#. I love this hitch. It is so much easier to hook and unhook and works flawlessly.

It may be hard to set it up at a dealer unless you have time to really make sure it done correctly as all the setup is on the trailer. Nothing to do on the truck but install the ball. Most techs no nothing about it. But it is easy if you stand by and read the instructions and see that the tech follows them.

I have no hesitancy in recommending the Andersen. You'll love it.