I had to make a bunch of frames similar to that and found a half-lap joint to work well. If you set up your table saw, you can cut a bunch of them very quickly, in one operation. Run the piece through a number of times, nibbling away the material so the depth and length of the lap are the same on each. A bandsaw works too but requires two set-ups. Assembly with glue and a couple of small brads, and the wood will bust before the joint.
I took a good look at the spline today as the glue was dry. It's nice and strong, which I like, and resists racking, which is good when pulling on a door.
One way or another, I need to slay this dragon as soon as possible.
One way or another, I need to slay this dragon as soon as possible.
My next step was to try using a spline joint at the corners.
After the glue dries tomorrow, I'll see how that seems to hold together. Perhaps that will work much better.
I can go a little deeper with the spline, but I figured I'd try one that is nearly 1/2 way through the one member, and used a piece of 1/4" plywood as the spline.
We'll see how that holds up tomorrow.
After the glue dries tomorrow, I'll see how that seems to hold together. Perhaps that will work much better.
I can go a little deeper with the spline, but I figured I'd try one that is nearly 1/2 way through the one member, and used a piece of 1/4" plywood as the spline.
We'll see how that holds up tomorrow.
Well, the wife told me to take the weekend off since it was New Years, so I figured perhaps I should.
Back at it today, and another idea shot to ... smithereenes....
I started to try to assemble the first frame for one of the doors in the bath area, and just blew it up.
Just in case you thought that it may have been way too thin ....
Yup, just a 1/16" shy of 3/4", or 11/16" if you prefer. So, that didn't work out well. On one of them, I even drilled out a hole for the screw in the secondary member, and it still split.
Back at it today, and another idea shot to ... smithereenes....
I started to try to assemble the first frame for one of the doors in the bath area, and just blew it up.
Just in case you thought that it may have been way too thin ....
Yup, just a 1/16" shy of 3/4", or 11/16" if you prefer. So, that didn't work out well. On one of them, I even drilled out a hole for the screw in the secondary member, and it still split.
PastorCharlie wrote:fulltimin wrote:PastorCharlie wrote:fulltimin wrote:
I spent some time tonight looking at some options for the doors to cover the shelves in the bath wall. Yes, I said doors, with an s.
A single door that's about 12" wide and over 6 feet tall, is just not going to work well. So, I decided to split them up into 3 doors, each about 2 feet tall.
That will be easier to manage.
After spending too much time on options, I settled on a frame and panel design, something like below. This just shows the frame without the panel inside.
That means I'll be working on that tomorrow.
I like to use folding louver doors and make them operate separate for such occasions. I have used decorative doors to accomplish what you are working on.
HERE
After a little thought, folding doors in a moving rv, doesn't sound like the best idea. Maybe I am missing something.
Separate the folding doors and make them into two regular hinged doors. I installed seven shelves in a 6'8" opening such as you are working with, and it holds a massive number of items and storage.
I hadn't thought of splitting them in the middle. Hmmmmmm.....
fulltimin wrote:PastorCharlie wrote:fulltimin wrote:
I spent some time tonight looking at some options for the doors to cover the shelves in the bath wall. Yes, I said doors, with an s.
A single door that's about 12" wide and over 6 feet tall, is just not going to work well. So, I decided to split them up into 3 doors, each about 2 feet tall.
That will be easier to manage.
After spending too much time on options, I settled on a frame and panel design, something like below. This just shows the frame without the panel inside.
That means I'll be working on that tomorrow.
I like to use folding louver doors and make them operate separate for such occasions. I have used decorative doors to accomplish what you are working on.
HERE
After a little thought, folding doors in a moving rv, doesn't sound like the best idea. Maybe I am missing something.
Separate the folding doors and make them into two regular hinged doors. I installed seven shelves in a 6'8" opening such as you are working with, and it holds a massive number of items and storage.
PastorCharlie wrote:fulltimin wrote:
I spent some time tonight looking at some options for the doors to cover the shelves in the bath wall. Yes, I said doors, with an s.
A single door that's about 12" wide and over 6 feet tall, is just not going to work well. So, I decided to split them up into 3 doors, each about 2 feet tall.
That will be easier to manage.
After spending too much time on options, I settled on a frame and panel design, something like below. This just shows the frame without the panel inside.
That means I'll be working on that tomorrow.
I like to use folding louver doors and make them operate separate for such occasions. I have used decorative doors to accomplish what you are working on.
HERE
After a little thought, folding doors in a moving rv, doesn't sound like the best idea. Maybe I am missing something.
