cancel
Showing results for 
Search instead for 
Did you mean: 

Help with pc board on basement a/c on 96 Winnebago vectra

mailman90902002
Explorer
Explorer
I have a 96 Winnebago vectra with a basement air unit model#6795B832 and the resistors on the pc board numbers R34 and R35 are bad and the color coding is faded so bad you can't make out what they are. Would anyone have a picture of a pc board for that model or know how I could find out the replacements I need. Thank you
11 REPLIES 11

crasster
Explorer II
Explorer II
Yeah, there is a source of the problem outside of those resistors UNLESS it was a one time thing... Approach the fix with caution, and if you fix it with resistors, test it WHILE WATCHING and don't just leave it on over night. I would totally test it for a while before trusting.
4 whopping cylinders on Toyota RV's. Talk about great getting good MPG. Also I have a very light foot on the pedal. I followed some MPG advice on Livingpress.com and I now get 22 MPG! Not bad for a home on wheels.

rgatijnet1
Explorer III
Explorer III
It is a very rare instance where a resister goes bad. Some other component has probably failed and caused excessive current to overheat the resisters. You could chase this problem for a long time by replacing parts but without a schematic and an understanding of the PC board's operation, it all may be a waste of time. Buy the replacement board and move on to other things that are more important.

ArchHoagland
Explorer
Explorer
Have you tried measuring the resistors with an ohm meter.

You need to find out why excessive current was going through them, enough so that they were overheated.

I'd suggest a new board as others have mentioned.
2004 Monaco La Palma 36DBD
Workhorse W22 8.1 Gas Allison 1000, 7.1 mpg

2000 LEXUS RX300 FWD 22MPG 4020 LBS
US Gear Brakes

cdl2
Explorer
Explorer
I replaced the boards on my roof top units, but then I had to buy a new thermostat.
Everything works fine now.

gfs1943
Explorer
Explorer
I don't know your model number ac unit, but I've had good success getting ac parts (including pc board for my basement air) from Makarios RV (www.makariosrv.com). Very fast shipping and, so far, everything I've ordered from them was the exact part number I needed.
gfs1943
USAF, Retired (1962 - 1983)
2006 Monaco Diplomat 40PRQ
2006 Honda CR-V

Ivylog
Explorer III
Explorer III
I realize this does not answer your question and probably not want to you hear...A friend with basement air once the extended warranty ran out gave up on it and put two roof units on. During the three year extended warranty it paid over $2000 fixing it and when it broke again on his dime he gave up on fixing. Made it into a basement storage area when he threw it away.
This post is my opinion (free advice). It is not intended to influence anyone's judgment nor do I advocate anyone do what I propose.
Sold 04 Dynasty to our son after 14 great years.
Upgraded with a 08 HR Navigator 45’...

mailman90902002
Explorer
Explorer
Thank you all for the help. I have already removed the resistors and you can't tell what value they are. I know I could buy one but I've been out a lot of money on this a/c unit and actually I just finished putting in both blower motors and when I was hooking the wires up I noticed the burnt capacitor and resistors. When I bought the Winnebago the guy said it just needed the outside blower motor but anyone can tell you anything and he might've honestly thought that was all that was wrong. I know I'm trying to cut a corner and probably shouldn't after replacing everything else but really don't want to buy a new one unless I just have to. The previous owner had the one blower motor unwired and the wires were just dangling around in the unit so I thought maybe they could've touched and maybe blowed the capacitor and resistors. If that's not logical please chime in cause I have no experience with electrical repair.

Sam_Spade
Explorer
Explorer
rgatijnet1 wrote:
or, if you have to, purchase a new PC board from him.


This is probably your best bet.

Resistors typically don't just "go bad"......but burn out acting something like a fuse when some other active component fails and sorts out.

Or to put it another way, it is HIGHLY unlikely that the resistors are the only thing that has failed on the board.
'07 Damon Outlaw 3611
CanAm Spyder in the "trunk"

Mandalay_Parr
Explorer
Explorer
I would go for a new board unless you can determine what caused the resistor failure.
The resistors may be just a symptom like a fuse.

Maybe final an electrical person to help you.
Jerry Parr
Full-time
2005 Mandalay 40B
Cat C7 350, 4 Slides
Blue Ox, Brake Buddy
2004 CR-V Toad
jrparr@att.net
602-321-8141
K7OU - Amateur Radio
Kenwood Radios
ARRL, W5YI, & LARC VE
SKYWARN Weather Spotter

rgatijnet1
Explorer III
Explorer III
You might ask this seller if he could give you the info on the resisters, or, if you have to, purchase a new PC board from him. Coleman PC board

mlslcan
Explorer
Explorer
I have found that sometimes the side against the board will not be as faded as the exposed side. I have been able to read the color bands on that side on some resistors when I used to do that type of repair.

If you have already removed them from the board and still can not make out the bands then my tip will not be helpful.

Mike