Cordless drill for scissor jacks

[clearn4]

Looking to purchase a cordless drill to raise and lower the four scissor jacks on my TT. A make and model number with a strong tork just for that would be very helpful.
Thank you

[coolbreeze01]

Surprised no-one recommended a brace :B

[trail-explorer]

SoundGuy wrote:
...regardless, this thread fell off the rails by the 3rd post when impact drivers were recommended.

Yep, then the noise police showed up saying "you better not run that loud impact driver in my campground!"
Those same people are the ones that let their kids ride their bikes cross country through people campsites, screamin an yellin. (noise rules don't apply to them, just everyone else)

I thought the noise police limited themselves to the posts about Generac(ket) generators, but alas, they don't.

[trail-explorer]

uh... my red text is annoying as huntindogs blue text. yes, it's annoying (the blue)
Every reply he posts, has that hideous blue text.

[SoundGuy]

trail-explorer wrote:
No Surprise that this thread has topped 5 pages.

On my screen it's 10 pages 😛 ... regardless, this thread fell off the rails by the 3rd post when impact drivers were recommended. :R

Gotta ask though - what's the attraction of tomato red text? ... inspired by Huntindog's Smurf Blue text? :h

[trail-explorer]

No Surprise that this thread has topped 5 pages.

In another month, a new thread will pop up.

[trail-explorer]

Huntindog wrote:

Wild Card wrote:
Surprised no one has fashioned a motor to each jack and a central control for all 4 or 6.

Motors are available, but pricey. I am sure it has been done.

Electric stab jacks are available, but the wiring would be a nuisance to install after the fact. Cheap cordless drill from harbor freight, mo betta.

[Huntindog]

Wild Card wrote:
Surprised no one has fashioned a motor to each jack and a central control for all 4 or 6.

Motors are available, but pricey. I am sure it has been done.

[Wild_Card]

Surprised no one has fashioned a motor to each jack and a central control for all 4 or 6.

[trail-explorer]

DE88ROX wrote:

Seems like a lot of work to just lower the stabs. I could have them all hand cranked down, (with time left over) by the time it would take me to unwind the cord, go plug it in, walk around the trailer, pulling said cord, and then wind it up.

Exactly.

The point of using a cordless drill is to make it easier and faster.

[DE88ROX]

arkieguide wrote:
As opposed to using a battery drill, take a 12 volt drill remove the battery pak, solder in an ext cord put clamps on it,
hook to your TV battery, No run down battery problem and plenty of power to do the job.

Seems like a lot of work to just lower the stabs. I could have them all hand cranked down, (with time left over) by the time it would take me to unwind the cord, go plug it in, walk around the trailer, pulling said cord, and then wind it up.

Ill stick to my 18v Li-Ion cordless drill. The the only time I use it camping, is to raise/lower stabs. otherwise it just sits in the storage compartment. A full charge before i head out and will last weeks when its never used.

[deltabravo]

Holiday sales should result in some good deals.

[fallsrider]

18 volts is not necessary for stabs, as has already been stated. 12 volts would be plenty. I already had an 18 v. DeWalt, so that is what I use. I figure I can raise or lower all 4 stabs with the drill as fast as I could hand crank one stab.

[GrandpaKip]

6 week trip out west. Used a DeWalt 18 volt drill to raise, lower the stabilizers and some drilling of holes and attaching screws. Never had to charge the battery.
By the way, if you have Litium batteries, I wouldn't leave them in the charger. My BIL had a neighbor's house burn down because of the battery catching fire. Sorta like the Samsung phones.

[Bumpyroad]

drsteve wrote:

arkieguide wrote:

As opposed to using a battery drill, take a 12 volt drill remove the battery pak, solder in an ext cord put clamps on it,
hook to your TV battery, No run down battery problem and plenty of power to do the job.

Doesn't that kinda defeat the whole purpose of a portable tool?

it's a cheap way to continue to use a drill whose battery/charger are obsolete and not available.
bumpy

[drsteve]

arkieguide wrote:

As opposed to using a battery drill, take a 12 volt drill remove the battery pak, solder in an ext cord put clamps on it,
hook to your TV battery, No run down battery problem and plenty of power to do the job.

Doesn't that kinda defeat the whole purpose of a portable tool?