โJan-14-2015 05:51 PM
โJan-27-2015 04:30 PM
sdetweil wrote:Dutch & Di wrote:
I'm asking because I am curious. While the senors codes will not have to be re-entered because you put them on a different trailers, as long as you put them on the same wheel locations, it sounds to me, and I could be wrong, like you are talking about having to change the alarm parameters because the FW & car hauler carry different air 110 vs 80. That is just a matter of changing the parameter alarm settings. It seems you have a good work around with your 2nd monitor but it is not mandatory if you have more than one trailer. Di
agreed, not mandatory.. because you have to at least tab thru all the tires that are the same to get to the axles (trailers are expected to be the same on both sides on an axle) then have to set the upper and lower settings..
it was easier for me to just have two monitors, not move the sensors, and deal with it. If someone else needs to use the trailer, then they just mount the correct monitor on the bracket I made and off they go.
there is enough setup to get out the drive with the FW, I don't need to fiddle with the sensors and reprogramming the monitor too..
time vs money.. they are paid for, and will work for a long time.
if I get rid of a trailer, I have a whole working set to sell to someone.
โJan-27-2015 04:16 PM
Dutch & Di wrote:
I'm asking because I am curious. While the senors codes will not have to be re-entered because you put them on a different trailers, as long as you put them on the same wheel locations, it sounds to me, and I could be wrong, like you are talking about having to change the alarm parameters because the FW & car hauler carry different air 110 vs 80. That is just a matter of changing the parameter alarm settings. It seems you have a good work around with your 2nd monitor but it is not mandatory if you have more than one trailer. Di
โJan-27-2015 03:42 PM
โJan-27-2015 03:14 PM
sdetweil wrote:johndeerefarmer wrote:
Let's quit the bickering and get back to the discussion. I will throw out a new question: How easy would it be to move the sensors from one trailer to another? I don't mean the act of physically moving them but of having to recalibrate the sensors for the new tires. For example, I have a Columubus 295RL on order. I want a TPMS for it. I would also like to use the system on my 24' tandem axle trailer when I take the RZR's to Colorado. It would also be nice to use on my 25' gooseneck equipment trailer. If the tires on each trailer all had the same pressure it shouldn't make any difference but what if one tire had a rating of 80psi and the others 100psi?
The sensors seem to be fairly expensive at about 50 bucks apiece so buying 8 spare sensors doesn't make much sense. Also the batteries I assume would run down whether I used the sensors or not.
re-calibrating the sensors is a pita for me, cause you have to do them ALL, even the ones that didn't change. I bought a second monitor and sensors for all tires 4 FW, 4 trailer, 6 Dually . one monitor when using my FW and one when using my enclosed car hauler..
FW at 110lbs, car hauler at 80lbs..
I just use whichever monitor I need.
when I am away from whatever trailer, I turn off the trailer sensors in that monitor.
โJan-27-2015 09:46 AM
johndeerefarmer wrote:
Let's quit the bickering and get back to the discussion. I will throw out a new question: How easy would it be to move the sensors from one trailer to another? I don't mean the act of physically moving them but of having to recalibrate the sensors for the new tires. For example, I have a Columubus 295RL on order. I want a TPMS for it. I would also like to use the system on my 24' tandem axle trailer when I take the RZR's to Colorado. It would also be nice to use on my 25' gooseneck equipment trailer. If the tires on each trailer all had the same pressure it shouldn't make any difference but what if one tire had a rating of 80psi and the others 100psi?
The sensors seem to be fairly expensive at about 50 bucks apiece so buying 8 spare sensors doesn't make much sense. Also the batteries I assume would run down whether I used the sensors or not.
โJan-27-2015 08:46 AM
Dutch & Di wrote:
When you take the senors off one RV and put them on another, all you to do is install the sensors on the same wheel location. It will pick them up. If you put them on a different wheel location, they will show on the monitor but be monitoring the tire. Dijohndeerefarmer wrote:
Let's quit the bickering and get back to the discussion. I will throw out a new question: How easy would it be to move the sensors from one trailer to another? I don't mean the act of physically moving them but of having to recalibrate the sensors for the new tires. For example, I have a Columubus 295RL on order. I want a TPMS for it. I would also like to use the system on my 24' tandem axle trailer when I take the RZR's to Colorado. It would also be nice to use on my 25' gooseneck equipment trailer. If the tires on each trailer all had the same pressure it shouldn't make any difference but what if one tire had a rating of 80psi and the others 100psi?
The sensors seem to be fairly expensive at about 50 bucks apiece so buying 8 spare sensors doesn't make much sense. Also the batteries I assume would run down whether I used the sensors or not.
โJan-27-2015 08:45 AM
johndeerefarmer wrote:
Let's quit the bickering and get back to the discussion. I will throw out a new question: How easy would it be to move the sensors from one trailer to another? I don't mean the act of physically moving them but of having to recalibrate the sensors for the new tires. For example, I have a Columubus 295RL on order. I want a TPMS for it. I would also like to use the system on my 24' tandem axle trailer when I take the RZR's to Colorado. It would also be nice to use on my 25' gooseneck equipment trailer. If the tires on each trailer all had the same pressure it shouldn't make any difference but what if one tire had a rating of 80psi and the others 100psi?
The sensors seem to be fairly expensive at about 50 bucks apiece so buying 8 spare sensors doesn't make much sense. Also the batteries I assume would run down whether I used the sensors or not.
โJan-27-2015 08:44 AM
โJan-27-2015 08:37 AM
โJan-27-2015 08:07 AM
โJan-27-2015 07:25 AM
neal10a wrote:avvidclif1 wrote:justme wrote:fj12ryder wrote:
Hmm, a company that doesn't make the stem sensors claims the stem sensors are unreliable. Who'd a thunk.
Show me any statement by any stem monitor manufacturer that makes any claim like Valor. Also, misleading advertising is against the law.
Sheesh,
I have the TST system and am not changing.
You have the other system and are not changing.
You nor anyone else has shown proof that either is better or worse.
How about leaving that dead horse alone, nothing left but bones anyway....
I also have the TST monitor and are not changing, but I think this discussion is pertinent for those who are trying to decide which type of TPMS to get. When I purchased my unit, I did not consider temperature because I have always used my IR temperature gun to monitor the tires and hubs. If I was relying only on the TPMS device, I don't think I would get a stem mounted device. Especially after I got one and found that it and my IR gun never agree and the TST is most unreliable for temperature. However, it does well for pressure if you have the range extender.
โJan-27-2015 06:10 AM
avvidclif1 wrote:justme wrote:fj12ryder wrote:
Hmm, a company that doesn't make the stem sensors claims the stem sensors are unreliable. Who'd a thunk.
Show me any statement by any stem monitor manufacturer that makes any claim like Valor. Also, misleading advertising is against the law.
Sheesh,
I have the TST system and am not changing.
You have the other system and are not changing.
You nor anyone else has shown proof that either is better or worse.
How about leaving that dead horse alone, nothing left but bones anyway....
โJan-26-2015 07:08 PM
โJan-26-2015 02:32 PM
justme wrote:fj12ryder wrote:
Hmm, a company that doesn't make the stem sensors claims the stem sensors are unreliable. Who'd a thunk.
Show me any statement by any stem monitor manufacturer that makes any claim like Valor. Also, misleading advertising is against the law.