DC to DC charger
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โSep-01-2022 01:34 PM
Thanks, Jeff D
2020 Arctic Fox 865 short bed
2021 Nitro Z18
- Labels:
-
Truck Campers
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-28-2022 01:47 PM
Host Mammoth 11.5 on Ram 5500 HD
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-28-2022 12:10 PM
Bedlam wrote:
What I have not seen posted is the fact that even if you use like chemistry batteries in the camper and truck, the capacity and age of the different batteries also affects charging (in addition to the small gauge trailer plug wiring). When you look at the diesels with dual start batteries, they have to be changed out in matched sets to keep optimal charging and power delivery (discharging). Putting in a DC to DC charger helps overcome these differences.
My two lifePO4 (560ah) will charge at 50 amps until they are almost completely charged with the low internal resistance unlike lead acid or agm.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-28-2022 11:11 AM
Host Mammoth 11.5 on Ram 5500 HD
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-28-2022 09:21 AM
ticki2 wrote:Hemi Joel wrote:
I just use a pair of 8 gauge wires from the truck battery to the camper batteries. That eliminates the voltage drop of the 7 pin and puts a nice charge into the camper batteries whenever I drive. I use a 200 amp blade switch that is mounted on the truck battery to isolate the truck battery when the situation calls for it, but that is rare.
The reason itโs working for you , and also for me , is the age of the truck . Newer trucks , last decade , have smart charging , meaning as soon as the starting batteries are satisfied charging goes way down , so the house batteries would get very little , especially with the voltage drop.
That is not true on newer GM HD trucks, my 2019 Chevy 2500HD sits above 14 volts, when changing my batteries it will ramp up to just above 15 volts @ 50amps.
According to the above statement I should have a smart alternator, but I have yet to see this mysterious lowering of voltage a few people on here keep stating. So maybe Ford and Ram do but my 2013 and 2019 Chevys donโt or if they do the alternator is smart enough to ramp up under heavy load.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-28-2022 08:04 AM
Hemi Joel wrote:
I just use a pair of 8 gauge wires from the truck battery to the camper batteries. That eliminates the voltage drop of the 7 pin and puts a nice charge into the camper batteries whenever I drive. I use a 200 amp blade switch that is mounted on the truck battery to isolate the truck battery when the situation calls for it, but that is rare.
The reason itโs working for you , and also for me , is the age of the truck . Newer trucks , last decade , have smart charging , meaning as soon as the starting batteries are satisfied charging goes way down , so the house batteries would get very little , especially with the voltage drop.
'02 GMC DRW D/A flatbed
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-28-2022 07:26 AM
Bottom line. The DC to DC converter just works and works well so I arrive at my destination with fully charged batteries and a cold refrigerator every time. I went with the combo Renogy MPPT and DC to DC all in one (DCC50S) to replace my PWM solar controller while I was at it. It gives 25 amps from solar and 25 amps from the truck with priority from solar. It will also charge the truck battery from solar if it gets low when you are parked for a long time. For me it was the right option and I should have added one a long time ago. It is also LiFePO4 compatible so when I upgrade batteries I only need to change the setting. If your rig charges while driving, or you don't need it to, then a DC to DC charger is not for you. For the rest of us.... they are awesome.
2016 Ford F250 4x4 gas, 3.73, airbags, bigwig, homemade stableloads, 20" wheels with toyo open country II
Sold - 1989 Fleetwood Jamboree Class C
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-28-2022 07:17 AM
Hemi Joel wrote:theoldwizard1 wrote:Hemi Joel wrote:
I just use a pair of 8 gauge wires from the truck battery to the camper batteries. That eliminates the voltage drop of the 7 pin and puts a nice charge into the camper batteries whenever I drive.
It has been proven 100s of times, that with modern vehicles, large gauge wires will NOT give you a 100% charge on your auxillary battery bank.
Some charge, yes. Just not 100%.
That makes no sense at all. The alternator doesn't know how many batteries are connected to it. It senses voltage. Batteries that are connected equalize over time.
Regardless, it has been working for me for over 10 years. If you want to buy a device to charge your 12 volt batteries better than a 12 alternator that was designed to charge 12 volt batteries, that's your call.
what you seem to be forgetting is that a altanator output is for charging starting batteries, and as long as you use thoes in your camper/trailer/motorhome for house batteries you'll be fine, might not have that much capacity but you'll charge them up good. the problem comes into when you go to different types of batteries like deep cycle, gell, lithium etc. they require different charge profiles for efficient and proper charging in order to get charged fully and with out doing dammage to the battery its self. a dc to dc charger alows you to charge using proper profiles for your battery type alowing longer life and proper charging.
2016 Cougar 330RBK
1991 Slumber Queen WS100
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-26-2022 08:31 PM
With lead acid house bank and lead acid starter I had charging. Enough that a 60 amp fuse fell on its sword.
My upgrade was to dual #8 (oem was #8) with twin 50 amp automatic circuit breakers. My ammeter maxes out at 70 amps--and I did have occasions where it would not display.
The lead acid were replaced with telcom jars, and whoops there was no charging from the alternator to the house unless I was running the microwave or other heavy draw. In fact it regularly sent power to the alternator. I replaced the starter battery with an AGM. No improvement.
My 20 amp renogy 20 amp dc to DC charger is sending up to 19.6 amps to the house bank. It is NOT a short run and is #8 wire. There is no voltage sensor.
I'm happy as a clam to have charging going on.
My ride is a 28 foot Class C, 256 watts solar, 556 amp-hours of Telcom jars, 3000 watt Magnum hybrid inverter, Sola Basic Autoformer, Microair Easy Start.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-26-2022 05:09 PM
A DC to DC charger placed near the alternator, without remote sense, does not solve this wiring problem, voltage will still be low. Placed near the load, or with remote sense near the load, it band-aids the problem: It will boost the voltage back to where is it supposed to be, at the cost of drawing even more current through the inadequate wires.
You need to address the wiring problem first, then consider a DC to DC charger. Or don't run large house loads (like the refer) on DC.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-26-2022 11:28 AM
theoldwizard1 wrote:Hemi Joel wrote:
I just use a pair of 8 gauge wires from the truck battery to the camper batteries. That eliminates the voltage drop of the 7 pin and puts a nice charge into the camper batteries whenever I drive.
It has been proven 100s of times, that with modern vehicles, large gauge wires will NOT give you a 100% charge on your auxillary battery bank.
Some charge, yes. Just not 100%.
That makes no sense at all. The alternator doesn't know how many batteries are connected to it. It senses voltage. Batteries that are connected equalize over time.
Regardless, it has been working for me for over 10 years. If you want to buy a device to charge your 12 volt batteries better than a 12 alternator that was designed to charge 12 volt batteries, that's your call.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-26-2022 10:52 AM
theoldwizard1 wrote:
Of course, you now know that wiring upgrade is not required when you get a new truck !
No, I don't know that.
I can't envision how the excessively long wire run of smaller gauge wiring of the stock truck wiring (on a new truck) will provide the amperage I see with my upgraded system
2018 Arctic Fox 992 with an Onan 2500i "quiet" model generator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-26-2022 10:23 AM
deltabravo wrote:
I mounted my Victron Orion in the camper as shown here
I already did a cable upgrade between the truck can camper back in 2015. Here's that project
Of course, you now know that wiring upgrade is not required when you get a new truck !
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-26-2022 10:20 AM
Hemi Joel wrote:
I just use a pair of 8 gauge wires from the truck battery to the camper batteries. That eliminates the voltage drop of the 7 pin and puts a nice charge into the camper batteries whenever I drive.
It has been proven 100s of times, that with modern vehicles, large gauge wires will NOT give you a 100% charge on your auxillary battery bank.
Some charge, yes. Just not 100%.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-26-2022 07:54 AM
I already did a cable upgrade between the truck can camper back in 2015. Here's that project
2018 Arctic Fox 992 with an Onan 2500i "quiet" model generator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
โNov-17-2022 09:48 AM
Hemi Joel wrote:
I just use a pair of 8 gauge wires from the truck battery to the camper batteries. That eliminates the voltage drop of the 7 pin and puts a nice charge into the camper batteries whenever I drive. I use a 200 amp blade switch that is mounted on the truck battery to isolate the truck battery when the situation calls for it, but that is rare.
I added dual #8 wires. When I switch to telcom jars--no more charging. I do have manual control over the 200 amp solenoids I added. The dc to DC charger was, for me, a huge improvement.
My ride is a 28 foot Class C, 256 watts solar, 556 amp-hours of Telcom jars, 3000 watt Magnum hybrid inverter, Sola Basic Autoformer, Microair Easy Start.