Moreride step above

[Bob_Vaughn]

I am looking at installing the more ride step above steps but no where can I find out how long they are......when held level with the camper floor how long are they? I need to know so before I spend the money I need to know if they will clear the wall of my enclosed rv port when I deploy them .....

[wvcampers]

I measured my 4 step Mor-ryde system at 90 degrees to the outside camper wall. It is 51" minimum to deploy. By measuring to third step it looks to be 38" and the second would be 25". I hope this helps.

[neschultz]

jplante4 wrote:

Bob Vaughn wrote:

PawPaw_n_Gram wrote:
The more I think about this, I think the distance that is important is the full length when 90 degrees from the trailer, i.e. the swing clearance.

After they are deployed, the distance the steps extend will be less than the swing clearance required when bringing them in or out.

It is a shame that MORryde doesn’t have those numbers available on their web site because that is a fixed number that doesn’t change with the individual rig mounting.

This is exactly what I am trying to determine.....

Well, we have a display model in the store. I'll be there tomorrow. I'll measure the step height and the 90° distance and we can make a guess as to the ratio of step height to swing distance. I think it's a 2 stepper.

My earlier post shows that the 3 step unit is 38” for a 32” height.

[jplante4]

Bob Vaughn wrote:

PawPaw_n_Gram wrote:
The more I think about this, I think the distance that is important is the full length when 90 degrees from the trailer, i.e. the swing clearance.

After they are deployed, the distance the steps extend will be less than the swing clearance required when bringing them in or out.

It is a shame that MORryde doesn’t have those numbers available on their web site because that is a fixed number that doesn’t change with the individual rig mounting.

This is exactly what I am trying to determine.....

Well, we have a display model in the store. I'll be there tomorrow. I'll measure the step height and the 90° distance and we can make a guess as to the ratio of step height to swing distance. I think it's a 2 stepper.

[Bob_Vaughn]

PawPaw_n_Gram wrote:
The more I think about this, I think the distance that is important is the full length when 90 degrees from the trailer, i.e. the swing clearance.

After they are deployed, the distance the steps extend will be less than the swing clearance required when bringing them in or out.

It is a shame that MORryde doesn’t have those numbers available on their web site because that is a fixed number that doesn’t change with the individual rig mounting.

This is exactly what I am trying to determine.....

[PawPaw_n_Gram]

The more I think about this, I think the distance that is important is the full length when 90 degrees from the trailer, i.e. the swing clearance.

After they are deployed, the distance the steps extend will be less than the swing clearance required when bringing them in or out.

It is a shame that MORryde doesn’t have those numbers available on their web site because that is a fixed number that doesn’t change with the individual rig mounting.

[Bob_Vaughn]

ependydad wrote:
Have you reached out directly to MorRyde?

Yes, but have received no response yet...

[ependydad]

Have you reached out directly to MorRyde?

[neschultz]

Just measured my 3step MorRyde and it needs 38” clearance 90 degrees from the TT side to deploy. TT floor is about 32” from ground for the 3 step unit.

[Bob_Vaughn]

ford truck guy wrote:
I was looking into the possibility of swapping mine for the 4 step... I was at a dealer and walked off right around 5’ with the step parallel to the driveway.

I have a row of arbvorbites that block that side of the trailer, and that is too close for us..

Thanks that is what I needed to know....

[ford_truck_guy]

I was looking into the possibility of swapping mine for the 4 step... I was at a dealer and walked off right around 5’ with the step parallel to the driveway.

I have a row of arbvorbites that block that side of the trailer, and that is too close for us..

[Bob_Vaughn]

ken56 wrote:
Have you gone to the web site for dimensions? I know they make 3 and 4 step models.

There web site does not say...

[ken56]

Have you gone to the web site for dimensions? I know they make 3 and 4 step models.

[PawPaw_n_Gram]

How far they extend out various depending upon the height of the rig, mounting positions.

I’ve seen some four step models extend out close to five feet and other four step models extend less than three feet.

I can’t find a maximum or minimum length on the MORryde web site. I remember the four steppers I’ve seen are close to five feet tall in the closed position.

[jplante4]

They have 2, 3 and 4 step configurations. We have a chart at the store that we give to customers to measure their height and width and that gives them the number of steps they need. I think this is it.

The feet extend about 6 inches independently so you can level them out.